607247
6
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Page.6
2. Loosen 2 screws on the left-hand side to open the glass window. Open the glass window all the way to
the right and then lift the window upwards out of the hinges (see page 9 figure 1).
3. Remove decorative log set and burner.
4. Dismantle burner unit. First detach the two cable connectors of the outlet safety (T.T.B.) on the left-
hand side of the burner unit and draw the wire out. Disconnect the gas pipe.
5. Dismantling combustion chamber. Remove the 2 screws at the top left and right of the combustion
chamber (see page 9 fig. 2). The combustion chamber can now be pulled (forward) out of the built-in
casing.
5.3 Installing the fireplace.
1. Installing the built-in casing
Mount the pipe mouth of the fire to the outlet duct. In order to achieve maximum heat emission, we recom-
mend insulating the built-in casing with non-combustible insulating material. Now slide the built-in casing
under the outlet duct and mount the pipe mouth to the casing, using the four self-tapping screws supplied. Do
this by tightening the screws upwards from the inside of the built-in casing. The built-in casing has an up-
right finishing edge which is placed against the opening of the mantelpiece during installation, thus deter-
mining the correct recessed depth. If you screw the front onto the built-in casing, you will be able to establish
whether the casing is flush with the wall. The height of the built-in casing can be adjusted by means of 4 ad-
justment bolts in the bottom of the casing. When the correct height has been set, you must fix the built-in
casing to the floor. Do this by means of screws and plugs in the holes made in the base plate. (Screws and
plugs are not supplied)
Warning
The fireplace should not be completely built-in. The front must remain free, in connection with expansion. If
a new mantelpiece is being built, the built-in casing must not bear the weight of the mantelpiece. A mantle
iron should always be used, therefore, which must not rest on the built-in casing and bears the complete
weight of the mantelpiece.
2. Assembly combustion chamber
Slide the combustion chamber into the built-in casing and secure it again by means of the 2 screws.
3. Connection burner unit
When mounting the burner unit, bring the lead of the fan out through the opening in the right-hand side of
the body. Slide the burner unit inside, well to the back of the combustion chamber.
4. Connection gas pipe
The gas pipe can be connected on either the right or the left-hand side. Fittings (3/8” G male thread) have al-
ready been mounted so that the burner unit can easily be dismantled later, for cleaning etc. The connection of
the gas pipe must be stress-free.
Important
Do not forget to reconnect the outlet safety (T.T.B.). Draw the lead for the safety device into the burner tray
and attach it to the two connectors of the thermocouple. If the connectors are not properly mounted, the fire
will not burn. In order to ensure that the fire functions well, the thermostat sensor should be placed outside
the fireplace, so that it reacts to the room temperature and not to the temperature of the fire. It must definitely
not be left inside the appliance.
Check
Use soapy water or a leak detector to check the gas tightness of the gas connection made. Put the plug for the
fan into the socket. Ignite the fire according to the operating instructions.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet VERSA LV-HV bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet VERSA LV-HV in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info