607255
7
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
Page.7
Remove the right-hand ( 10 ) / left-hand (9) and uppermost (7 ) glass holders, so that the window ( 19 ) can
be removed. NB: the lowest glass holder ( 8 ) need not be removed completely, but slightly loosened so
that the window ( 19 ) is supported during removal.
Carefully take the glass window to a safe place, to prevent it being broken or damaged.
First remove the casing bottom panel ( 18 ) by removing 4 screws. After this, the casing (17) can be taken
out by unscrewing the four M4 cross- head bolts in the outermost corners.
Now take the combustion unit out the box and mount this on the wall. Fix it with the 4 nuts and the cotter
bolts.
Fill the burner evenly with the lava stones supplied. If too many lava stones have been spilled beside the
burner and you wish to remove it, read the section entitled “Removing the burner”.
Warning: before you replace the window, please make sure that a restrictor plate is needed. See page 8.
Replace the glass window ( 19 ) in the reverse order to that used for its removal. Do not forget to re-tighten
the bottom glass holder (8 ).
The location of the gas main and the gas valve can now be determined and be connected to the fire. There
is a 3/8” gas connection located near the gas control, to which you can connect the pipe work. See also
“Connection to the gas supply”.
Installation of the fire can now be completed.
Attention: please check the pressure valves under and on top of the combustion chamber for posi-
tioning and tightness.
Remove the 2 bolts ( 11 ) in the bottom glass holder.
Place the casing ( 17 ) and the casing bottom panel ( 18 ) back on the fire.
The Decorative Window can now be carefully hung on the projections to the left and right (A) of the glass
holder at the top ( 7A ) and be secured by replacing the 2 bolts in the bottom glass holder.
In order to switch the fire on, see section 2 “Operating Instructions” on Page 4.
Removing the burner ( See Page 13 fig. 1 )
It is not absolutely necessary to remove the burner, but it is possible to take it out if you have lost too many lava
stone when filling the burner. In this case, proceed as follows:
First take out the left- hand recirculation plate ( 3 ) by removing the screw on the inside of the fire.
Move the burner slightly to the left first and then tilt it at a slight angle to take it out.
When you are ready to replace the burner, return all the parts in reverse order.
Connection to the gas main
Use a 1/2" gas tap with coupling in the supply pipe. The connection to the fire is fitted with a 3/8’ coupler. Take
care when connecting that the regulating equipment is not twisted and that no superfluous stress is induced. Also
ensure that the gas pipe is free of contaminants and sand. The accessibility of the gas tap must be guaranteed for
this fire. Check the joints for gas tightness after the connection has been made.
4. Concentric duct system
The concentric duct system consists of an inner duct of 100 mm diameter and an outer duct of 150 mm diameter.
These ducts are concentrically arranged. The combustion gases are extracted via the inner duct, while fresh air
for combustion flows in via the space between the inner and outer ducts. The concentric duct system enables
various connections.
Through the roof or through the external wall.
The route for this system can be laid out in various ways, but there are several important conditions.
The total permitted vertical duct length is 12 metres (the sum of the duct length and the calculated lengths
of the bends).
The horizontal duct length for a roof outlet must not exceed 5 metres, measured between bends.
90° bends have a calculated length of 2 metres.
45° bends have a calculated length of 1 metre.
The outlet can be placed at any arbitrary position on the roof surface or external wall (inlet and outlet in
identical pressure areas) but must satisfy current regulations.
In the case of a direct wall outlet, the maximum permitted duct length is the standard wall terminal length.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet Flat Fire M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet Flat Fire M in de taal/talen: Engels als bijlage per email.

De handleiding is 2,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info