607255
6
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
Page.6
Preparations for installing the Flat Fire
Always check all parts for possible damage or breakage. The Decorative Glass or Decorative Steel Front( de-
pending on whichever you have chosen) should be carefully taken out of the box. Put the Decorative window in a
place where it will not become damaged or broken. This also applies to the Decorative Steel Front. The box for
the Decorative Window or the Decorative Steel Front also contains a template which you can use in positioning
the fire ( See Page 15 ). First take the glass window off the fire to prevent any damage to the window during in-
stallation of the fire. See point 3 on page 5 “Installation instructions Flat Fire with concentric duct connection”.
Now take the accessories out the box with care, so that the fire can be removed and fixed to the wall. The fire is
now ready to be installed
3. Installation instructions for the Flat Fire with concentric duct connection
General instructions
The fire should only be installed and connected by a registered installer, in accordance with the local Gas
Appliance Instructions. Also see Page 3 “Important information”.
Never place the fire against or in a flammable wall.
The gas connection must be stress- free, to ensure no damage occurs to the gas regulating equipment.
Check the gas connections for leaks, using soapy water or leak detection spray. Light the fire in accordance
with the operating instructions and check that the shape of the flame is even.
After the first firing, you will need to remove any deposit left on the glass window.
Distances to non- combustible materials.
Non- combustible surfaces are defined as brick, marble, concrete etc. and also a number of man-made materials
impervious to flame. If in doubt, refer to the material manufacturer for further information before proceeding
with installation. It is recommended that there is at least 300mm clearance above the outlet grille. Minimum
clearance from the bottom of the outer frame to the floor must be 200mm, however, clear and easy access to the
controls located on the bottom side must be allowed for. Clearance to the sides of the heater is 100mm. Clearance
to the front of the heater is 1000mm. Care must be taken that no brickwork or other incombustible material pro-
trudes into the area immediately around the base of the heater or area underneath the heater in a way that is likely
to affect natural airflow into or around the heater.
Components of the fire ( See Page 13 fig. 1 )
1 Combustion unit 12 Flue connection 100mm
2 Burner 13 Air chamber
3 Recirculation plate 14 Wall brackets bottom
4 Injector bracket 15 Wall brackets top
5 Burner support 16 Flue connector 150mm
6 Pilot burner 17 Casing
7 Glass holder top 18 Bottom panel casing
8 Glass holder bottom 19 Glass window combustion chamber
9 Glass holder left 20 Decorative panel
10 Glass holder rigth 21 Decorative Steel front
11 Bold for front
Installing the fire
Caution: Before you install the fire, it is advisable first to read Section 4 “Concentric duct system” on Page 7,
regarding installation of the restriction sheet iron, if required
The box for the Decorative Glass ( 20 ) or the Decorative Steel Front ( 21 ) contains a template for use in
determining the position where the fire will be hung. Drill the holes for suspending the fire and the hole for
the concentric duct. Insert the cotter bolts provided into the four drilled holes and then remove the nuts
from the cotter bolts.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet Flat Fire M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet Flat Fire M in de taal/talen: Engels als bijlage per email.

De handleiding is 2,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info