480572
10
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
7
PART 2 • English
English
symbol next the channel name. After you have marked all channels for locking, your changes will be saved by pressing
BACK. Now you will have to enter your PIN every time you are switching to a locked channel. If you are not entering the
PIN, the receiver will show after a few seconds the picture of the last watched channel until you enter the correct PIN.
For more information, please refer to “Parental Settings” in chapter 5.4 CONFIGURATION.
Note Above described actions for Move and Delete can only be applied for All Channels” list mode. If you
are in a different channel list mode, a message will be shown to change to this mode or not.
5.2 Favourites
In MAIN MENU screen, use the pq buttons to select Favourites and press OK to enter this menu. In this menu, you
can add channels to the favourite list. With BACK you can always cancel actions and exit the actual menu or submenu.
Select desired channels you want to add to the list. Use the
pq buttons to go through the channel list, furthermore
you can use the RED (PG up) and GREEN (PG down) button to scroll page wise. With OK you switch to the selected
channel. The frequency and the satellite name of the selected channel will be displayed below its picture. With OK you
can mark and unmark channel to FAV group, your changes will be saved as soon you press BACK.
5.3 Installation
In MAIN MENU screen, use the pq buttons to select Installation and press OK to enter this menu. The Installation
Menu consists of following sub-menus: Antenna Installation, First Time Installation, Automatic Search, Manual Search,
Load Settings and Save Settings.
5.3.1 Antenna Installation
In submenu Installation, use the pq buttons to select Antenna Installation and press OK to enter this menu. Here you
can access all important settings concerning your dish installation and you will be able to see signal level (strength)/
signal quality (signal to noise ratio) for selected satellite and transponder. With BACK you can always cancel actions and
exit the actual menu or submenu.
Satellite: Currently approx. 50 preset satellites exist, such as Astra, Hotbird, EuroBird, Turksat etc.
and 4 user defined satellites as User1 - User4. Use the
u button and pq buttons to
select the satellite which is in your area of reception from the list. By pressing OK at the
selected satellite, you can enter a new name for it. Therefore you can use the NUMERIC
buttons.
Dish Type: Use the
tu buttons to change the used dish type. You can choose between DiSEqC 1.0,
DiSEqC 1.2 and GOTO X. If you have chosen the DiSEqC 1.2 or GOTO X you can enter the
according setup menu with OK.
DiSEqC 1.0: Use this setup if you are using dish installation with one or multiple fixed dishes. The
default setup for your country specific satellite is already done (AUT-Astra19.2, GER-
Astra19.2, CZE-Astra23.5, SLO-Astra23.5) on DiSEqC input 1. If your installation contains
another satellite or satellites, please setup corresponding SAT on DiSEqC input 2, 3 and 4.
5.3.1.1 DiSEqC 1.2 Setup Menu
Use this setup if you are using dish installation with motorized antenna. After confirming DiSEqC 1.2 setting with OK
in Dish Type, you will enter the DiSEqC 1.2 Setup Menu. With BACK you can always cancel actions and exit the actual
menu or submenu.
Transponder Settings: If you have chosen a satellite from the installed SAT table, the corresponding reference
transponder is already set. If you want to change the values for reference TP, press OK to
enter its submenu. Use the NUMERIC buttons to enter new values and use
pq buttons
to navigate. Your changes will be saved as soon you press BACK.
Go to Angle: Use the
pq buttons to navigate and NUMERIC buttons to enter a value for the angle you
want to go to. Some DiSEqC 1.2 positioners do not support the “go to angle” command. If
your positioner does not support this function, you can enter 000 for the angle in order to
turn the positioner to the reference zero position.
Motor Speed: Use the
tu buttons to change the speed between fast and slow.
Drive Motor: Use the
tu buttons to drive motor to west or east. To drive the motor towards a specific
direction,
tu buttons should be kept pressed.
Enable/Disable Limits: Use the
tu buttons to enable or disable the software limits for defined east or west limits.
Store Position: If your adjustment has reached the maximum signal strength and quality for the desired
position, you can press OK in order to save this setting.
Set East Limit: If you press OK at the position your motor is currently moved to, it will be saved as east
limit. Now your motor will not move to the east over this set limit.
Set West Limit: If you press OK at the position your motor is currently moved to, it will be saved as west
limit. Now your motor will not move to the west over this set limit.
Recalculate Positions: Use this function to restore possible misaligned dish position. Setup one of the satellite
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Strong SRT 7500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Strong SRT 7500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info