720561
15
Verklein
Vergroot
Pagina terug
1/146
Pagina verder
13
ENGLISH
6. Press the spool down GENTLY and rotate it until you feel it
drop into place and then push to snap into place. (When in
place, the spool will turn a few degrees left and right freely).
7. Take care to keep the line from becoming trapped under
thespool.
8. Fit the spool onto the appliance as described in Replacing
SpoolAssembly.
Replacing Spool Assembly (Fig.K, L)
WARNING: The use of any accessory not
recommended by STANLEYFATMAX for use with this
appliance could behazardous.
WARNING: Do not use any blades, or any
accessory or attachment other than those recommended
by STANLEYFATMAX on this trimmer. Serious injury or
product damage mayresult.
Reload nylon line (either bulk or prewound replacement spool)
as shown in thismanual.
USE ONLY 1.65 mm DIAMETER ROUND NYLON MONOFILAMENT
LINE. Do not use serrated or heavier gauge line, as they will
overload the motor and cause overheating. This line is available
at your local dealer or authorized servicecenter.
1. Remove battery fromappliance.
2. Press the release tabs
19
on the spool cap
18
, and remove
the spool cap from the spool housing
10
(Figure K).
3. For best results, replace spool and line with
STANLEYFATMAX Model # STZST12169/STZST121693
or replace cap only with STANLEYFATMAX
Model#STZST1326.
4. If lever in base of housing becomes dislodged, replace in
correct position before inserting new spool intohousing.
5. Remove any dirt and grass from the spool cap and
spool housing.
6. Unfasten the end of the cutting line and guide the line into
the eyelet.
7. Take the new spool and push it onto the boss
20
in the
housing. Rotate the spool slightly until it isseated.
8. The line should protrude approximately 5-136mm from
thehousing.
9. Align the release tabs on the spool cap with the slots in the
spoolhousing.
10. Snap the spool cap back on by depressing release tabs and
pressing into spoolhousing.
11. Push the cap onto the housing until it snaps securely
intoplace.
NOTE: Make sure that cover is fully positioned, listen for two
audible clicks to ensure both release tabs are correctly located.
Power the appliance on. In a few seconds or less you’ll hear the
nylon line being cut automatically to the properlength.
NOTE: Other replacement parts (guards, spool caps, etc.) are
available through authorized service centers.
Rewinding Spool from Bulk Line (use only
1.65 mm ROUND diameter line) (Fig.A, M, N)
Bulk line is also available for purchase from your local retailer.
NOTE: Hand wound spools from bulk line are likely to become
tangled more frequently than STANLEYFATMAX factory wound
spools. For best results, factory wound spools arerecommended.
1. Remove battery fromappliance.
2. Remove the empty spool from the appliance as described in
Replacing SpoolAssembly.
3. Remove any remaining cutting line from the spool
21
.
4. Make a fold at the end of the cutting line at about 19
mm. Feed the cutting line into one of the line anchoring
slots
22
.
5. Insert the 19 mm end of the bulk line into the hole
23
in
the spool adjacent to the slot. Make sure the line is pulled
tight against thespool.
6. Wind the cutting line onto the spool in the direction of the
arrow on the spool. Make sure to wind the line on neatly
and in layers. Do notcrisscross.
7. When the wound cutting line reaches the recesses
24
cut
theline.
8. Fit the spool onto the appliance as described in Replacing
SpoolAssembly.
MAINTENANCE
Your STANLEYFATMAX power tool has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon
proper tool care and regularcleaning.
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
The charger and battery pack are notserviceable.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
WARNING: Blow dirt and dust out of the
main housing with dry air as often as dirt is seen collecting
in and around the air vents. Wear approved eye protection
and approved dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the materials used in
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SFMCST933 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SFMCST933 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 14,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info