Handleiding Stanley SFMCST933 (pagina 14 van 146) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

720561

Verklein

Vergroot

Pagina terug

1/146

Pagina verder

ENGLISH

To extend runtime, pull the speed control switch back toward

the battery housing

12

into the "LO" position. This mode is best

for larger projects that require more time tocomplete.

To accelerate the trimmer, push the speed control switch

3

forward toward the auxillary handle

5

into the "HI" position.

This mode is best to cut through heavier growth and for

applications that need higherRPM.

NOTE: When in "HI" mode, runtime will be decreased as

compared to when trimmer is in "LO"mode.

Trimming (Fig.H, I)

With the trimmer on, angle it and swing side to side as shown

in FigureH.

Maintain a cutting angle of 5° to 10° as shown in Figure I. Do not

exceed 10°. Cut with the tip of the line.

Maintain a minimum distance of 610 mm between the guard

and your feet as shown in FigureI.

Convert to Edging Mode (Fig.J)



CAUTION: The wire edge guide should only be

used when in the edging mode.

The trimmer can be used in trimming mode or edging mode to

trim overhanging grass along lawn edges and flower beds. To

convert the trimmer to edging mode:

1. Remove the battery from thetrimmer.

2. Grasp the turn-to-edge collar

7

and pull down as shown

in Figure J.

3. Rotate the turn-to-edge collar 180° counterclockwise as

shown in Figure J., until the handle snaps back into the

upper half of the trimmer.

4. To return to trimming position, pull the turn-to-edge

collar up and rotate the head clockwise back to its

originalposition.

NOTE: You will experience faster than normal cutting line wear

if the trimmer line is positioned directly over the sidewalk or

abrasivesurface.

Edging Mode Operation (Fig.A, H)



WARNING: When being used as an edger,

stones, pieces of metal and other objects can be thrown

out at high speed by the line. The trimmer and guard are

designed to reduce the danger.

However, MAKE SURE that other persons and pets are at least

100' (30 m) away. Optimum cutting results are achieved on

edges deeper than 50mm.

• Do not use this trimmer to createtrenches.

• Using the wire edge guide

9

, guide thetrimmer.

• Position the wire edge guide on the edge of the sidewalk or

abrasive surface so the cutting line is over the grass or dirt

area to beedged.

• To make a closer cut, slightly tilt thetrimmer.

Helpful Cutting Tips (Fig.K)

• Use the tip of the string to do the cutting; do not force string

head into uncutgrass. Use edge guide along such things as

fences, houses and flower beds for bestpractices.

• Wire and picket fences cause extra string wear, even

breakage. Stone and brick walls, curbs, and wood may wear

stringrapidly.

• Do not allow spool cap

18

to drag on ground or

othersurfaces.

• In long growth, cut from the top down and do not exceed

305 mmhigh.

• Keep trimmer tilted toward the area being cut; this is the

best cuttingarea.

• The trimmer cuts when passing the unit from the left to

right. This will avoid throwing debris at theoperator.

• Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by thestring.

Cutting Line/Line Feeding

Your trimmer uses 1.65 mm diameter, ROUND nylon line. During

use, the tips of the nylon lines will become frayed and worn and

the special self feeding spool will automatically feed and trim

a fresh length of line. Cutting line will wear faster and require

more feeding if the cutting or edging is done along sidewalks

or other abrasive surfaces or heavier weeds are being cut. The

advanced automatic line feeding mechanism senses when more

cutting line is needed and feeds and trims the correct length

of line whenever it’s required. Do not bump unit on ground in

attempt to feed line or for any otherpurposes.

Clearing Jams and Tangled Line (Fig.K)



WARNING: Remove the battery from the

trimmer before making any assembly, adjustments or

changing accessories. Such preventive safety measures

reduce the risk of starting the applianceaccidentally.

From time to time, especially when cutting thick or stalky

weeds, the line feeding hub may become clogged with sap or

other material and the line will become jammed as a result. To

clear the jam, follow the steps listedbelow.



CAUTION: To avoid appliance damage, if the

cutting line protrudes beyond the trimming blade, cut it off

so that it just reaches theblade.

1. Remove the battery from thetrimmer.

2. Press the release tabs

19

on the spool cap

18

, and remove

the spool cap from the spool housing

10

(Figure K).

3. Pull the nylon line spool out and clear any broken line or

cutting debris from the spool area.

4. Place spool and line into spool cap with line “parked” in

slotsprovided.

5. Insert the line end through the appropriate hole in the

spool housing. Pull slack line through until it pulls out of the

holdingslots.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Stanley SFMCST933 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info