812374
42
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
Factory settings
All settings can be reset, returning the controller to its delivery state.
All of the controller‘s parametrization, statistics, etc. will be lost irrevocably. The controller must then be commissioned once
again.
Time & Date
Serve to set the current time and date.
For time-dependent functions such as circulation and anti-legionella and the evaluation of system data, it is essential that the
time is accurately set on the controller. Please note that the clock continues to run for about 24 hours if the mains voltage is inter-
rupted, and afterward must be reset. Improper operation or an incorrect time may result in data being cleared, recorded incor-
rectly or overwritten. The manufacturer accepts no liability for the recorded data!
Starting aid
For some solar systems, in particular for vacuum tube collectors, the measurement recording on the collector sensors may be too slow or
imprecise, because the sensor is often not on the warmest spot. With an activated starting aid, the following procedure occurs: If the tem-
perature on the collector sensor increases within a minute by the value defined under “increase”, the solar circulation pump will be turned on
for the set “purging time” so that the medium to be measured is transported to the collector sensor. If there is still no normal switching con-
dition through this, there will be a 5 minute block time for the start wizard function.
This function should only be activated by a technician if problems occur with the measurement recording. Observe in particular
the instructions from the collector manufacturer.
The menus "Purging time" and "Increase" are only displayed when the starting aid function is set to "On".
Purging time
If the temperature on the collector sensor increases within a minute by the value defined under “increase”, the solar circulation pump will be
turned on for the set “purging time” so that the medium to be measured is transported to the collector sensor. If the set ΔT is not reached, a 5-
minute circulation pause time for the starting aid function will apply.
Increase
If the temperature at the collector reaches within a minute the value defined, the solar pump is turned on for the duration of the purging time.
Global radiation sensor
With the global radiation sensor, a start-up operation can be triggered depending on the solar
radiation. If the set radiation intensity exceeded at the sensor, the start-up aid is activated and the solar pump is switched on for the set rins-
ing time. If within this time no start condition is reached, the start-up function is blocked for the set time.
Radiation sensor
The sensor input can be defined here, to which the global radiation sensor is connected.
Radiation intensity
If the radiation intensity set here is exceeded in watts See " Starting aid " on page 42per at the radiation sensor, the starting aid function
will be triggered,
Blocking time
Here a blocking time in minutes can be defined. Within this the starting aid function is disabled.
Daylight saving time
If this function is activated, the controller automatically changes to winter time or summer time (DST, Daylight Savings Time).
Eco Display Mode
In Eco Display Mode the backlight of the display is switched off if no buttons are pushed for 2 minutes.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sorel LTDC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sorel LTDC in de taal/talen: Engels als bijlage per email.

De handleiding is 5.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Sorel LTDC

Sorel LTDC Gebruiksaanwijzing - Nederlands - 36 pagina's

Sorel LTDC Gebruiksaanwijzing - Deutsch - 50 pagina's

Sorel LTDC Gebruiksaanwijzing - Français - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info