812374
41
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
The heat quantity data in the “Constant flow” mode only consists of calculated values for the functional inspection of the system.
Flow temperature sensor (X)
In this menu, it is set which sensor is used to measure the flow temperature.
Return flow sensor
In this menu, you can set which sensor is used to measure the return flow temperature.
Glycol type
In this menu, the antifreeze used is set. If none is used, please set glycol proportion to 0.
Glycol percentage
The percentage of antifreeze in the medium.
Flow rate supply flow (X)
Nominal system flow.
The flow of the system in liters per minute, which is used as calculation basis for heat metering.
Offset ∆T
Correction factor for the temperature difference for heat metering
Since the collector temperature and the storage temperature can be used for the heat quantity metering, depending on the system, there
may be deviations from the displayed collected temperature to the actual previous temperature or the displayed storage temperature to the
actual return temperature. This deviation can be corrected with the adjustment value Offset ΔT
Example: displayed collector temperature 40°C, read previous temperature 39°C, displayed storage temperature 30°C, read return tem-
perature 31° means a setting of -20% (displayed ∆T 10K, actual ∆T 8K => -20% correction value)
VFS (X)
The type used of direct sensor is set in this menu.
VFS - Position
This menu is used to set whether the direct sensor was mounted in supply or return flow.
To prevent damage to the Vortex Flow sensor it is highly recommended to place it in the return flow. If contrary to this recom-
mendation it is used in the supply line, the maximum temperature has to be considered. (0 ° C to 100 ° C continuous operation
and short term -25 ° C to 120 ° C)
Reference sensor
The sensor to be used for heat metering is set here.
Sensor Calibration
Deviations in the temperature values displayed, for example. due to cables which are too long or sensors which are not positioned optim-
ally can be compensated for manually here. The settings can be made for each individual sensor in steps of 0.5 °C.
Settings are only necessary in special cases at the time of initial commissioning by the specialist. Incorrect measurement val-
ues can lead to unpredictable errors.
Commissioning
Starting commissioning help guides you in the correct order through the basic settings necessary for commissioning, and provides brief
descriptions of each parameter in the display. Pressing the ‚esc‘ key takes you back to the previous value so you can look at the selected
setting again or adjust it if desired. Pressing ‚esc‘ more than once takes you back to the selection mode, thus cancelling the commissioning
help (See " Commissioning help " on page 28).
May only be started by a specialist during commissioning! Observe the explanations for the individual parameters in these
instructions, and check whether further settings are necessary for your application.
41

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sorel LTDC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sorel LTDC in de taal/talen: Engels als bijlage per email.

De handleiding is 5.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Sorel LTDC

Sorel LTDC Gebruiksaanwijzing - Nederlands - 36 pagina's

Sorel LTDC Gebruiksaanwijzing - Deutsch - 50 pagina's

Sorel LTDC Gebruiksaanwijzing - Français - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info