620396
9
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
Siemens / Building Technologies / HVAC Products CE1G2218xx 24.04.2009 9/40
Difficult controlled systems:
Proper on / off controller with a switching differential of
0.5 C. (factory setting)
1.1.5 Periodic pump run
This function protects the pump against seizing during longer off
periods. Periodic pump run is activated for one minute every 24
hours at 12:00 (when pump run is activated, the flame symbol
appears on the display).
On the heating engineer level, change from the flashing CAL
symbol to the
symbol by turning the setting knob (factory
setting, periodic pump run off). Press to accept.
will flash (factory setting). Press the OK-knob to accept or
continue turning the setting knob. The
symbol for periodic pump
run on will flash. Press the OK-knob to accept (also refer to Fig.
).
1.1.6 Heating / cooling mode
On the heating engineer level, change from the flashing CAL
symbol to the heating / cooling symbols by turning the setting knob.
Press the OK-knob to accept, the
heating symbol will flash
(factory setting). Press the OK-knob to accept or con-tinue turning
the setting knob. The cooling symbol
will flash. Press the OK-
knob to accept (also refer to Fig
).
1.1.7 Protection mode
Use operating mode selector to select symbol (also refer to
Fig. ).
Adjustment of standard values (frost protection = 5 °C;
overheat protection = 35 °C) being done in temperature menu T by
setpoint
(refer to Operating Instructions).
2 Functional check
a) Check the display. If there is no display, check the correct fitting
and function of the batteries.
b) Comfort mode
c) Select temperature menu T and adjust the temperature setpoint
to 29 °C (refer to the Operating Instructions)
d) The relay must be energized and thus the actuating device
activated within one minute. Flame symbol
will appear
on the display. If that is not the case:
Check actuating device and wiring
The room temperature is possibly above 29 °C
e) Reset the setpoint temperature
to the initial value
(standard value 19 °C or individual setting)
f) Select the required operating mode
3 Reset
User-defined data:
Press the button behind the pin opening for at least one second:
this resets the user-specific settings to their default values (the
heating engineer settings will not be changed). The clock starts at
12:00. During the reset time, all sections of the display light up,
enabling them to be checked.
All user-defined data plus the heating engineer settings:
Press the button behind the pin opening together with the warmer
and colder buttons for at least one second.
After this reset, the factory settings will be reloaded (also refer to
section “Factory settings“ in the operating instructions).
4 Notes
REA23.03RF/SET is a set of units consisting of electric room
temperature controller/thermostat with a weekly timeswitch and
transmitter (REA23.03RF) and a RF receiver (REA-R.03/1)
The controller conforms to “Software Class A” and is for use in
“normal” pollution situation.
If the reference room is equipped with thermostatic radiator
valves, they must be set to their fully open position
Ensure that the local regulations for electrical installations are
complied with
Indications pour le montage et la mise en service des
REA23.03RF et REA-R.03/1
1 Emplacement des appareils
1.1 REA23.03RF et REA-R.03/1
Choisir un emplacement présentant le moins d'obstacle
possible à l'émission et la réception. Respecter les points
suivants, tant pour le REA23.03RF que pour le REA-R.03/1:
Eviter le montage sur des surfaces métalliques,
Eviter le montage à proximité de lignes électriques et des
appareils électroménagers, (PC, téléviseur, four à micro-
ondes, etc.)
Eviter de placer l'appareil derrière des composants
métalliques de grande taille susceptibles de faire écran à la
réception, ou des éléments de construction comportant un
grillage métallique à mailles serrées.
La distance entre l'émetteur et le récepteur ne doit pas
dépasser 20 m ou 2 étages.
1.2 REA23.03RF (régulateur/ émetteur)
Il est conseillé d’installer le REA23.03RF dans la pièce de séjour
principal (montage mural figure C, emplacement libre figure E
avec dispositf de pose)
L’appareil doit être placé de préférence dans la pièce de
séjour principale (montage mural, selon figure C,
emplacement libre, figure E avec support amovible).
Pour que la mesure de la température de l'air ne soit pas
faussée, monter l’appareil à un endroit à l'abri du
rayonnement solaire ou d'autres sources de chaleur ou de
froid.
Indications pour le montage mural :
min.
10 cm
2261Z03
1.3 REA-R.03/1 (récepteur)
Installer le récepteur à proximité de l’appareil à commuter
(par ex. chaudière murale, moteur thermique 2 points).
Veiller à ce que l’emplacement soit sec et protégé contre les
projections d’eau.
L’appareil convient pour la plupart des boîtes à encastrer. Il peut
être monté également directement en saillie sur le mur.
2 Vérification du câblage
Les raccordements sont détaillés dans le chapitre „Schéma des
connexions“.
Nota : Ne pas utiliser de câble plat, uniquement du câble plein
ou des câbles plats avec des embouts prémontés.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens REA23.03RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens REA23.03RF in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens REA23.03RF

Siemens REA23.03RF Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens REA23.03RF Gebruiksaanwijzing - English - 2 pagina's

Siemens REA23.03RF Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info