620396
8
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
8/40 24.04.2009 CE1G2218xx Siemens / Building Technologies / HVAC Products
6 Explanation to LED_1 and LED_2
LED_1 lights always in red:
LED_1 flashes in red:
LED_1 flashes 3 times in green:
LED_1 flashes 2 times in green:
LED_1 flashes 1 time in green:
LED_2 is always dark:
LED_2 lights always:
LED_2 flashes always:
LED_2 flashes briefly: Reception of control telegram
7 Finish mounting of REA-R.03/1
a) Switch off power
b) Mark location where REA-R.03/1 is currently fixed
c) If necessary loosen wiring
d) Mount receiver at location marked before according Fig. H to
M, wire completely and close housing
e) Switch on power
Commissioning the controller / transmitter REA23.03RF
1 Configuration
1.1 Accessing the heating engineer level
The heating engineer level will be enabled by pressing
simultaneously the warmer and colder buttons and by turning the
setting knob counter-clockwise and then clockwise (also refer to
Fig. G).
1.1.1 Calibrating the temperature sensor
After activating the heating engineer level, the CAL symbol will
flash. When pressing the OK-knob, the room temperature currently
measured flashes and can now be recalibrated by a maximum of ±
2 °C by turning the setting knob. To store the recalibration, press
the OK-knob (also refer to Fig.
).
1.1.2 Setpoint limitation
There are 2 setting choices available:
or
On the heating engineer level, change from the flashing CAL
symbol to the setpoint limitation symbol by turning the setting knob
clockwise (also refer to Fig.
).
Press the OK-knob to accept. 5...29 °C will flash (factory setting).
Press the OK-knob to accept or continue turning. Setting 16...29 °C
will flash.
Press the OK-knob to accept.
1.1.3 Optimum start control
On the heating engineer level, change from the flashing CAL
symbol to the optimum start control symbols
by turning the setting knob clockwise
(also refer to Figs.
and ).
Press the OK-knob to accept.
(factory setting) will
flash, optimization is switched off. Press the OK-knob to accept or
continue turning until you reach ¼ h/°C,
½ h/°C oder 1 h/°C. Press the OK-knob to accept.
1.1.4 Control mode
On the heating engineer level, change from the flashing CAL
symbol to the symbols of the various control modes by turning the
setting knob (also refer to Fig.
).
Press to accept.
(factory setting) will flash. Press the OK-knob
to accept or continue turning the setting knob to select one of the
following control modes:
, PID 6, PID 12 or . Press the OK-knob to accept the
required control mode.
A brief description of the control modes is given below (also refer to
Fig.
).
Self-learning
Adaptive control: Suited for all
standard applications.
PID 12 Normal controlled systems:
For locations with normal temperature variations.
PID 6 Fast controlled systems:
For locations with significant temperature variations.
Red on
Red off
No REA23.03RF linked
Red on
Red off
Si
g
nal stren
g
th too weak
Green on
Green off
Signal strength: Very good
1 2 3
1 2 3
Starting
sequence
Starting
sequence
Green on
Green off
Signal strength: Good
1 2
1 2
Starting
sequence
Starting
sequence
Starting
sequence
Green on
Green off
Signal strength: Satisfactory
1
1
Starting
sequence
Starting
sequence
1
Starting
sequence
Orange on
Orange off
Controlled device OFF
Orange on
Orange off
Controlled device ON
Orange on
Oran
g
e off
Learning mode active
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens REA23.03RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens REA23.03RF in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens REA23.03RF

Siemens REA23.03RF Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens REA23.03RF Gebruiksaanwijzing - English - 2 pagina's

Siemens REA23.03RF Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info