620396
7
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
Siemens / Building Technologies / HVAC Products CE1G2218xx 24.04.2009 7/40
Siting note for wall mounting:
min.
10 cm
2261Z03
1.3 REA-R.03/1 (receiver)
The receiver and switching unit should preferably be mounted
near the actuating device
Make certain that the mounting location is dry and protected
from splash water
The unit can be fitted to most commercially available recessed
conduit boxes or directly on the wall.
2 Check wiring
For the electrical connections, refer to “Connection diagram“.
Note: Do not use stranded wires, only solid wires
or stranded wires with ferrules.
3 Notes
The local regulations for electrical installations must be
complied with
If the reference room is equipped with thermostatic radiator
valves, they must be set to their fully open position
In the event of a power failure at the REA-R.03/1, the relay will
be deenergized.
If in normal operation REA-R.03/1 does receive for more than
25 minutes a very weak or no control telegram from
REA23.03RF, LED_1 starts to flash in red.
If control telegram is still understood correctly, receiver
continues with normal operation. If control telegram is not
understood anymore, relay remains in last position being
switched to before.
As soon as REA-R.03/1 does receive any correct control
telegram from REA23.03RF again, receiver continuous with
normal operation
In case of error, REA-R.03/1 switches off relay approximately
60 minutes after reception of last correct control telegram.
The controlled device is also switched off and LED_1 flashes
in red.
As soon as REA-R.03/1 does receive any correct control
telegram from REA23.03RF again, receiver continuous with
normal operation
Commissioning RF Set
1 Switch on REA23.03RF
Remove the battery transit tab (also refer to Fig. F): As soon
as the battery transit tab is removed, the unit starts to operate.
2 Mount REA-R.03/1 temporarly
If possible, mount receiver temporarly in a first run (e.g. double
coated tape). Doing that, location of best RF reception can be
identified later on.
See clause “5 Find location of best reception“
Completely wire and mount REA-R.03/1 temporarly. Proceed
according Fig. H to M (please also close front cover)
3 Link REA-R.03/1 with REA23.03RF
a) Switch on power at REA-R.03/1: LED_1 (Fig. H) lights always
in red or flashes in red
b) Press the "RESET“ button on REA-R.03/1 for about
4 seconds: The orange LED_2 (Fig. H) will flash very fast
and briefly (stored address of REA23.03RF will be erased)
c) Press the "SET“ button (set / learn) for about 3 sec. until the
orange LED starts flashing slowly and continuously: Receiver
is now in learning mode
d) The receiver stays max. 25 minutes in learning mode. If no
learning telegram from REA23.03RF is received during that
period of time, repeat steps b) and c) again
e) Press the ESC button
ESC
on REA23.03RF for about
4 seconds. Learning telegram is transmitted
f) If REA-R.03/1 receives learning telegram, the orange LED_2
flashes fast and briefly
g) If the orange LED_2 is steady on, the relay is energized
(= controlled device ON)
h) If the orange LED_2 is dark, the relay is deenergized
(= controlled device OFF)
i) Depending on the operating state, REA23.03RF repeats the
ON or OFF control telegram every 3 minutes. With this the
relay will be switched ON or OFF according to control telegram
latest after 3 minutes
j) If REA-R.03/1 does not receive any correct control telegram
within 60 minutes, controlled device is being switched off and
LED_1 flashes in red
k) In the event of a power failure at the REA-R.03/1, the relay will
be deenergized.
4 Site REA23.03RF
Site REA23.03RF at preferred location for mounting at wall or
setting up with stand. Remove the unit from its base by
proceeding according to Fig. A:
- for wall mount, refer to Figs. B, C and D
- for set up with stand, refer to Fig. E
Also refer to “Mounting and siting notes REA23.03RF and
REA-R.03/1“
5 Find location of best RF reception
a) Switch off power at REA-R.03/1
b) Switch on REA23.03RF, site at prefered location and press
override button
for about 4 seconds: REA23.03RF
transmits test telegrams every 2 seconds. Transmission of test
telegrams stopps automatically after 10 minutes or after
pressing either “ESC” button or override button
c) Switch on power at REA-R.03/1
d) Observe both LEDs on REA-R.03/1 from a distance of
2…3 meters
e) Orange LED_2 must flash briefly every 2 seconds.
Does LED_2 not flash every 2 seconds, distance between
REA23.03RF and REA-R.03/1 is too far. Mount REA-R.03/1
closer to REA23.03RF
f) LED_1 shows received signal strength of last telegram:
LED_1 flashes red: Signal is too weak to get a durable
durable link. Mount REA-R.03/1
closer to REA23.03RF
LED_1 flashes green: We distinguish between three
signal strenghts:
Very good (flashes 3x),
Good (flashes 2x) and
satisfactory (flashes 1x).
As soon as LED_1 flashes in green,
link between REA23.03RFand
REA-R.03/1 is basically ok.
g) Move REA-R.03/1 within an area of approximately 1 square
meter to find location of best RF reception. Always observe
LEDs from a distance of 2…3 meters.
To get a durable link, we recommend to site REA-R.03/1 at
a location where signal strength is at least “Good”.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens REA23.03RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens REA23.03RF in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens REA23.03RF

Siemens REA23.03RF Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens REA23.03RF Gebruiksaanwijzing - English - 2 pagina's

Siemens REA23.03RF Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info