Handleiding Sencor SRV 2010 (pagina 11 van 13) (Engels)

759455

Verklein

Vergroot

Pagina terug

1/13

Pagina verder

10/2018

- 11 -

■ In the automatic cleaning mode, along-the-wall cleaning mode and spiral

cleaning mode, the control button LED indicator A9 is lit green. In the return

to charging station mode, the control button LED indicator A9 will be lit red.

DIRECTION BUTTONS ▲◄►

■ The direction buttons D8, D9 andD18 can be used to manually control the

movement of the robotic vacuum cleaner on the floor. When the vacuum

cleaner is moved on the floor, the operation of the motorised side rotary

brushes A18 and A23 is synchronised with the movement of the motorised

wheels A15 and A21. The vacuuming function is disabled.

■ When the direction button D8 is pressed, the robotic vacuum cleaner will

move forward. For continuous movement forward, hold down button D8.

When button D8 is released, the vacuum cleaner will stop moving.

■ When direction button D9 is pressed, the vacuum cleaner will turn

anticlockwise. To continuously turn the vacuum cleaner, hold down button D9.

When button D9 is released, the vacuum cleaner will stop moving.

■ When direction button D18 is pressed, the vacuum cleaner will turn clockwise.

To continuously turn the vacuum cleaner, hold down button D18. When

button D18 is released, the vacuum cleaner will stop moving.

■ If the robotic vacuum cleaner is docked in the charging station B1, when

any direction button is pressed the robotic vacuum cleaner will move

approximately 80 cm from the charging station B1, turn around by 180° and

switch to the stand-by mode. Press a direction button again to control the

direction of movement.

■ If the robotic vacuum cleaner is in a cleaning mode or returning to the

charging station, when any direction button is pressed the vacuum cleaner

will stop and switch to the stand-by mode. Press adirection button again to

control the direction of movement.

■ In the manual movement control mode, the robotic vacuum cleaner moves

according to the direction buttons and sensors A11 and A27 prevent collisions

with obstacles and falling from stairs.

SETTING AND CANCELLING REPETITION OF THE AUTOMATIC CLEANING

MODE

■ This function enables the setting of repetition for the automatic cleaning

mode or to cancel it. The robotic vacuum cleaner will automatically perform

the set number of cleaning cycles. At the end of each cleaning cycle, it will

automatically return to the charging station to recharge the battery B3 and

the next cleaning cycle will always commence when the charging cycle has

finished. When acleaning cycle starts, the number of repetitions will always

be lowered by one cycle.

■ Hold down button B11 to switch to the mode for setting the number of

automatic cleaning cycles. Indicator D3 will start flashing and the number of

cleaning cycles will be shown on display D1. The default setting is 0 cleaning

cycles. Amaximum of 3 repetitions may be set. In the event that the automatic

cleaning mode repetition mode function is already set, then the number of

remaining cycles will be shown on display D1. Select the number of repetitions

using buttons D9 (+) andD18 (–). Hold down button D11 to save the setting.

The saving of your setting is confirmed by an acoustic signal.

Note:

The mode for setting the number of cleaning cycles will automatically

be cancelled and display D1 will switch to the time display mode if no

changes are made within 10 seconds. The previously saved setting will

remain in memory.

■ If the robotic vacuum cleaner is parked in the charging station B1 and the

charging cycle is finished, the robotic vacuum cleaner will immediately

commence the automatic cleaning cycle and the number of repetitions will be

reduced by one cycle. If the robotic vacuum cleaner is in the charging mode,

the charging cycle will first finish and only then will the vacuum cleaner start

the automatic cleaning cycle.

■ If the robotic vacuum cleaner is not docked in the charging station B1 and is

switched to the stand-by mode or sleep mode, it is necessary to start the first

cleaning cycle manually. This automatically lowers the number of repetitions

by one cycle. In the event that the operation of the robotic vacuum cleaner

is interrupted and then started again, the number of cycles will, likewise, be

lowered by one cycle.

■ When the robotic vacuum cleaner is in the automatic cleaning mode, it will

complete it first and return to the charging station B1. When the charging

cycle is complete, the robotic vacuum cleaner will start the automatic cleaning

cycle and the number of repetitions will be reduced by one cycle.

■ The repetition of automatic cleaning mode function is cancelled by pressing

button D8 once in the repetition setting mode. Indicator D3 and the number

of repetitions will turn off. The robotic vacuum cleaner will emit aconfirmation

acoustic signal. The function can also be cancelled by setting the number

of repetitions to 0 cycles or by turning the vacuum cleaner off and on using

switch A20.

SETTING THE CURRENT TIME

■ Hold down button D12 to switch to the time setting mode. The minutes will

start flashing on display D1. Use the direction buttons D9 (+) andD18 (–) to set

the minutes. Hold down the button to speed up the setting process.

■ Press button D12 to switch to the hour setting mode. The hours will start

flashing on display D1. Use the direction buttons D9 (+) andD18 (–) to set the

hours. Hold down the button to speed up the setting process.

■ Hold down button D12 to save the current setting. The robotic vacuum cleaner

will confirm the setting by an acoustic signal.

■ The current time setting mode will automatically be cancelled and display D1

will switch to the time display mode if no changes are made within 10 seconds.

The setting will not be stored in memory.

SETTING AND CANCELLING THE PLANNED CLEANING FUNCTION

■ This function is used to set a time in advance, when the robotic vacuum

cleaner is to start automatic cleaning.

■ Hold down button D19 to switch to the time setting mode for planned

cleaning. Indicator D13 will be lit and the minutes will be shown on display D1.

Use the direction buttons D9 (+) andD18 (–) to set the minutes. Hold down the

button to speed up the setting process.

■ Press button D19 to switch to the hour setting mode. The hours will start

flashing on display D1. Use the direction buttons D9 (+) andD18 (–) to set the

hours. Hold down the button to speed up the setting process.

■ Hold down button D19 to save the setting. The robotic vacuum cleaner will

confirm the setting by an acoustic signal. Display D1 will switch to the current

time display mode. After another 30 seconds the remote control B4 will switch

to sleep mode.

■ Press button D19 to wake up the remote control B4 from the sleep mode. Press

button D19 again to show the time of the planned cleaning. After 5seconds

the display D1 will switch back to the current time display mode. If the planned

cleaning function is not set, then in the display planned cleaning mode,

display D1 will show “--:--”.

Note:

The planned cleaning time mode will automatically be cancelled and

display D1 will switch to the time display mode if no changes are made

within 10 seconds. The initial setting will remain saved in memory.

■ This function enables the setting of only asingle planned cleaning time. When

the automatic cleaning at aplanned time is started, the function is reset and

for another planned cleaning it is necessary to set this function again.

■ In the event that at the time of the planned cleaning, the robotic vacuum

cleaner is in the cleaning mode or returning to the charging station B1, the

planned cleaning will only take place next time at the planned cleaning time

when the robotic vacuum cleaner is not in operation.

■ The planned cleaning function and repetition of automatic cleaning can be set

simultaneously. When the robotic vacuum cleaner starts automatic cleaning at

aplanned time, the number of repetitions will be reduced by one cycle.

■ The planned cleaning function is cancelled by pressing button D8 once in the

planned cleaning time setting mode. This is confirmed by an acoustic signal.

The previous time setting will remain stored in memory. Likewise, turning the

power supply to the vacuum cleaner on and off using switch A20 will cancel

the function. In the event that batteries are removed from the remote control

B4 or they go flat, the planned cleaning function and time setting will be reset.

SLEEP MODE AND WAKING FROM SLEEP MODE

■ The remote control B4 will automatically switch to sleep mode after 30

seconds of inactivity. In this mode, only the time is shown on the display D1.

■ Press any button to wake up the remote control B4 from the sleep mode. The

display D1 will show other information such as the operating mode indicator,

battery level, planned cleaning function indicator D13 and the repeated

automatic cleaning function D3, if set. For the display D1 to show the correct

information, the robotic vacuum cleaner must be within signal range of the

remote control.

TROUBLESHOOTING

■ The robotic vacuum cleaner is itself able to identify problems and report them

via awarning acoustic signal. If this happens, the vacuum cleaner will stop and

when one of the control buttons on the display D1 of the remote control B4

is pressed, it will show the error message code. In the case of control buttons

D11, D12 and D19, the error message code is shown only when the button is

used to confirm asetting.

■ The table below will help you identify the cause and to remedy the problem.

Once the problem is resolved, you may put the vacuum cleaner back into

operation.

Sencor SRV 2010 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info