Handleiding Sencor SRV 2010 (pagina 12 van 13) (Engels)

759455

Verklein

Vergroot

Pagina terug

1/13

Pagina verder

10/2018

- 12 -

ERROR

MESSAGE

CODE

CAUSE SOLUTION

C01 Wheels are not in contact

with the floor.

Place the vacuum cleaner on

the floor so that both wheels

are in contact with the floor.

C03 The bottom front sensor is

soiled (dust, dirt, etc.)

Set switch A20 to position

0 (off) and clean the sensor

using aclean and dry wiping

cloth.

C04 The bottom left sensor is

soiled (dust, dirt, etc.)

Set switch A20 to position

0 (off) and clean the sensor

using aclean and dry wiping

cloth.

C05 The bottom right sensor is

soiled (dust, dirt, etc.)

Set switch A20 to position

0 (off) and clean the sensor

using aclean and dry wiping

cloth.

C06 The motor of the vacuum

cleaner is not working.

Set switch A20 to position

0 (off). To resolve the

malfunction, please contact an

authorised service centre.

C07 Foreign items (cables, parts

of clothing, etc.) have wound

themselves on to the front

left brush A18.

Set switch A20 to position 0

(off) and remove the items

that are blocking brush A18.

C08 Foreign items (cables, parts

of clothing, etc.) have wound

themselves on to the front

right brush A23.

Set switch A20 to position 0

(off) and remove the items

that are blocking brush A23.

C09 Foreign items (cables, parts

of clothing, etc.) have wound

themselves on to the left

wheel A15.

Set switch A20 to position 0

(off) and remove the items

that are blocking the wheel

A15.

C10 Foreign items (cables, parts

of clothing, etc.) have wound

themselves on to the right

wheel A21.

Set switch A20 to position 0

(off) and remove the items

that are blocking the wheel

A21.

C12 The temperature of the

battery B3 is too high.

Set switch A20 to position

0 (off) and before using the

robotic vacuum cleaner again,

allow the battery B3 to cool

down.

C13 The voltage of the battery B3

is too low.

The battery B3 needs to be

charged. Place the robotic

vacuum cleaner manually into

the charging station B1. Make

sure that there is aconnection

between the charging

contacts.

C16 andC17 Error on the right or left part

of the bumper A10.

Set switch A20 to position 0

(off). Release the jammed part

of the bumper A10.

C18 The robotic vacuum cleaner

is tangled.

Move it to open space.

C19 Error of battery B3. Replace the old battery B3

with anew one.

C21, C22

andC23

Error of anti-collision sensor

located in the front bumper

A10 (on the left, in the

middle or on the right)

Set switch A20 to position 0

(off) and using aclean and dry

wiping cloth, clean the entire

window of the front bumper

A10.

■ In the event that the robotic vacuum cleaner stops and you are unable to put

it back into operation, try turning switch A20 off and then on again. If the

problem persists, please contact an authorised service centre.

CLEANING AND MAINTENANCE

■ Prior to cleaning, turn off the robotic vacuum cleaner by setting switch A20 to

position 0 (off) and disconnect the charging station B1 from the power socket.

■ Empty the dust container A4 after each use. Press button A7 to open the lid A1

and remove the dust container A4. Release the clip on the dust container A4

and open the lid A5. Remove the dirt from the dust container A4. For hygiene

reasons, we recommend doing this away from living areas. Properly close the

lid A5. Aclick indicates that the lid A5 is closed. Put the dust container A4 back

in its place and close the lid A1.

■ Remove and clean the mop after every use. Wash the textile sleeve B7 by hand

in lukewarm water with the addition of a small amount of gentle washing

powder and allow it to dry naturally. Wipe the mop head B6 using lightly

dampened cloth and then wipe it thoroughly dry.

■ Clean the inflow filters A2 and A3 once per week. After emptying out the dust

container A4, remove the frame with the filters A2 and A3. Take filter A2 out

of the frame and then tap out both filters A2 and A3 away from living areas. In

the event of greater soiling, you may wash the filters A2 and A3 under running

lukewarm water. After washing them, allow the filters A2 and A3 to dry

naturally. Put the cleaned filters A2 and A3 back in their place. Before putting

the filters A2 and A3 back in their place, make sure that they are completely

dry. For hygiene reasons, we recommend that filters A2 and A3 are replaced

every three months.

Attention:

To prevent damaging the vacuum cleaner, make sure that both inflow

filters A2 and A3 are properly installed in their place.

■ At least once per week or more frequently, clean the front swivel wheel A25,

motorised wheels A15 andA21, central rotary brush A17, suction opening

A14, rubber squeegee A22, side rotary brushes A18 and A23, charging

contacts A26, sensors A11 andA27 and charging station B1. First remove any

coarser dirt from the swivel wheel A25 and the motorised wheels A15 and

A21. Then clean them around their entire perimeter using alightly dampened

cloth and wipe them dry. Do not forget to also clean the area around the

wheels. Release and remove the clamp of the central rotary brush A16 and

take out the rotary brush A17. Use adry wiping cloth to clean out the suction

opening A14, rubber squeegee A22 and the area in which the rotary brush

A17 is housed. Remove any dirt and material (wound on hair, animal fur, etc.)

from the rotary brush A17. Insert it back in its place and secure it using the

clamp A16. Remove the side rotary brushes A18 and A23. Remove any dirt

and material from the rotary brushes A18 and A23 and from the area where

they were attached. After cleaning them, reattach them. If they are worn out,

replace them with anew ones. Wipe the sensors A11 located on the bumper

A10, sensors A27 on the underside of the vacuum cleaner, the surface of the

charging station B1 including the charging contacts C5 using asoft dry wiping

cloth.

■ Regularly wipe the remaining surfaces of the robotic vacuum cleaner using

asoft dry wiping cloth.

■ For cleaning, never use abrasive cleaning products, solvents, etc.

■ Neglecting cleaning and maintenance may negatively affect the functioning

of the vacuum cleaner and lead to its reduced performance.

TECHNICAL SPECIFICATIONS

POWER ADAPTER

Type .................................................................................................................................. T-ZC11.1

Input ...........................................................................................100−240 V~, 50/60 Hz, 0.3 A

Output ..................................................................................................................... 18 V , 0.8 A

Protection class ............................................................................................................................ II

CHARGING STATION

Type ................................................................................................................................... T-ZC11.2

Input ......................................................................................................................... 18 V , 0.8 A

Output ..................................................................................................................... 18 V , 0.8 A

ROBOTIC VACUUM CLEANER

Power input ...........................................................................................................................40 W

Battery ........................................................................................Li-Ion / 14.4 V / 2,850 mAh

Charging time .......................................................................................................................3–5 h

Maximum operating time with fully charged battery ............................... 80 minutes

Dust container capacity ................................................................................................ 230 ml

Noise level ........................................................................................................................74 dB(A)

The declared noise emission level is 74 dB(A), which represents alevel Aof sound

power with respect to areference sound power of 1 pW.

Explanation of technical terminology

Safety class for electrical shock protection:

Class II – Electrical shock protection is provided by double or heavy-duty

insulation.

We reserve the right to change text and technical specifications.

Sencor SRV 2010 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info