782189
15
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
15
m Risques résiduels
La machine est construite selon l’état actuel de la tech-
nique et conformément aux réglementations reconnues
en matière de sécurité. Le travail avec la machine peut
toutefois présenter des risques résiduels.
En cas de guidage ou d’appui incorrects de l’outil
devant être rectifié, la meule rotative présente des
risques de blessures pour les doigts et les mains.
En cas de maintien ou de guidage incorrects, risque
de blessures par des outils éjectés.
Le courant présente un risque en cas d’utilisation de
lignes de branchement électrique non conformes.
Des risques résiduels non apparents sont toutefois
encore possibles malgré toutes les mesures prises.
Il est possible de réduire les risques résiduels en
respectant les consignes de sécurité et l’utilisation
conforme ainsi que les instructions de service.
Montage de la scie à découper, Fig. 1
1 Boulon de serrage: pour enlever la lame de scie.
2 Protecteur de lame: protège vos mains de blessures.
3 Appui de lame: maintient la lame en position.
4 Souffleur de poussière: permet au rebord de la piéce
d‘œuvre de ne pas s‘empoussiérer. Dirigez toujours
très précisément le tuyau vers I‘endroit des pièces
d‘œuvre sur lequel vous travaillez.
5 gulateur de vitesse
6 On/Off switch
7 Échelle d‘angles: à I‘aide de cette échelle, vous
pouvez lire le degré d‘inclination de la pièce
d‘œuvre.
8 Allumage
9 Arbre flexible avec mandrin
10 10 Jauge d’ajustage pour lames de scie sans
goupilles
Mise en service
Réglage de la table de sciage, Fig. 2
Aménagement de I‘échelle d‘angles
Ouvrez le bouton de blocage (1) et mettez la table de
sciage en angle droit par rapport à la lame de scie.
Utilisez un angle de 90° pour mesurer I‘angle droit
entre la lame et la table. La lame de scie devrait être
étroite ment appuye contre I‘angle à 90°,
Quand la distance entre la lame et I‘angle à 90° est
au minimum, refermez leboutonde blocage. La table
devrait alors étre à 90° par rapport à la lame de scie.
Ouvrez la vis de blocage de I‘échelle et mettez
I‘indicateur en position zéro. Serrez la vis. Corrigez
en suite la vis de position zero sous la table. Prenez
garde s‘il vous plait : I‘échelle d‘angles est une pièce
supplé mentaire utile, mais elle ne devrait pas étre
utilisée pour des travaux de précision. Utilisez du bois
m Remaining hazards
The machine has been built using modern technology in
accor dance with recognized safety rules. Some remaining
hazards, how ever, may still exist.
Long hair and loose clothing can be hazardous when
the work piece is rotating. Wear personal protective
gear such as a hair net and tight fitting work clothes.
Saw dust and wood chips can be hazardous. Wear per-
so nal protective gear such as safety goggles and a dust
mask.
The use of incorrect or damaged mains cables can lead
to injuries caused by electricity.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may still
be present.
Remaining hazards can be minimized by following the
instructions in „Safety Precautions“, „Proper Use“ and
in the entire operating manual.
Do not force the machine unnecessarily: excessive
cutt ing pressure may lead to rapid deterioration of the
blade and a decrease in performance in terms of finish
and cutting precision.
Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
Scroll Saw Design Features, Fig. 1
1 Clamping screw: for removing the saw blade.
2 Blade guard: protects your hands from injury.
3 Work piece holder
4 Shavings blower: keeps the workpiece area free from
dust.
5 electronical speed switch
deco 402: Speed switch
6 On/Off switch
7 Angle scale: you can read the angle position of the ta-
ble with this scale.
8 Lighting
9 Flexible shaft with drill chuck
10 Setting gauge for saw blades without pin
Installation
Setting the saw bench, Fig. 2
Setting the angle scale
Release the star button (1) and bring the saw bench
(2) to a right angle (3) in relation to the saw blade.
Use a 90° angle tc measure the right angle between
the blade and the bench. The saw blade be 90° to
the angle.
Close the star button again when the distance between
the blade and the 90° angle is at a minimum. The
bench should then be at 90° to the saw blade.
Release the lock screw and bring the indicator to the
zero position. Fasten the screw. Please note: the angle
scale is a useful piece of supplementary equip ment,
but should not be used for precision work. Use scrap
wood for saw tests, adjust the bench if neces sary.
Note: The bench should not be on the motor block, this can
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach SD1600F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach SD1600F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 2.55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info