699578
28
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
26 Programming CA-6
Messaging – programming telephone number
FS87 - programming telephone number 1 (HEX)
FS88 - programming telephone number 2 (HEX)
FS89 - programming telephone number 3 (HEX)
FS90 - programming telephone number 4 (HEX)
The functions FS87 to FS90 are used to program the telephone numbers to which the
control panel sends alarm messages. Each telephone number can have up to sixteen
digits and special characters. The numbers are to be programmed in the same way as in
the function FS4.
FS95 - programming assignment of partitions and messages (BIT)
At the moment an alarm occurs, the control panel can send an alarm message to four
telephone numbers. As the system can be divided into independent partitions, the
messaging should depend on which partition is alarming. The FS95 function assigns the
telephone numbers to partitions and defines which message is to be sent.
To program this parameter it is necessary to assign partition and number of message,
which is to be sent to each telephone number. The AB, AB LEDs indicate (in binary
format) the telephone number, which is being programmed.
The LEDs 1 and 2 show the assignment of consecutive numbers to partitions:
1 - telephone number for A partition
2 - telephone number for B partition
A telephone number can be associated with one or two partitions.
The LEDs 5 to 6 show the message, which is sent to a consecutive number:
5 - message 1 to pager
6 - message 2 to pager
Note: If no message for the paging system is assigned to the number, the panel will
send a voice message from the synthesizer.
EXAMPLE:
programming of the following settings (assuming that LEDs 1 to 8 for all numbers are off)
1
st
telephone number - message no. 1 (pager), in case of alarm in A & B partitions,
2
nd
telephone number - message no. 2 (pager), in case of alarm in A partition,
3
rd
& 4
th
tel. number - voice message from synthesizer, in case of alarm in B partition.
[12345] [#] - enter the service mode
[9][5] [#] - call the function (lower B diode is blinking - 1
st
telephone number)
[1] - LED 1 goes on (number 1 assigned to A partition)
[2] - LED 2 goes on (number 1 assigned to B partition)
[5] - LED 5 goes on (message 1 assigned to number 1)
[#] - confirm assignment for number 1 (A LED is blinking - 2
nd
number)
[1] - LED 1 goes on (number 2 assigned to A partition)
[6] - LED 6 goes on (number 2 assigned to B partition)
[#] - confirm assignment for number 2 (A and B LEDs are blinking- 3
rd
number)
[2] - LED 2 goes on (number 3 assigned to B partition)
[#] - confirm assignment for number 3 (upper B LED is blinking - 4
th
number)
[2] - LED 2 goes on (number 4 assigned to B partition)
[#] - confirm assignment for number 4
Messaging – programming of PAGER messages
FS96 - programming message 1 (POLPAGER format)
FS97 - programming message 2 (POLPAGER)
The message is programmed in the same way as in case of direct telephone messaging to
the POLPAGER receiver. The control panel saves in its memory the consecutively
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's

Satel CA-6 Installatiehandleiding - English - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info