699578
23
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
CA-6 SATEL 21
FS61 - programming zone tamper alarm codes (HEX)
The codes programmed with this function are reported when the CA-6 detects violation of
the tamper contact in 2EOL/NC and 2EOL/NO line, which triggers a tamper alarm.
FS63 - programming zone violation codes (HEX)
The function is used for programming the zone violation codes. The zone violation code is
transmitted to the monitoring station in case of:
violation of an armed delayed zone (of entry/exit, interior delayed, delayed type)
when the control panel has started the entry delay countdown,
violation of an armed counting zone when the number of violations still does not
trigger an alarm,
violation of a day/night zone when it is disarmed,
violation of an armed zone when the zone already signals an alarm - during the
alarm no subsequent alarms are signaled, and the consecutive detector activation is
recorded in the event log as “zone violation”; when the alarm signaling is over, each
next violation of the detector will trigger an alarm.
Note: If the alarms and violation codes are not program for all zones than the station
may not be notified of the alarm. If one of the control panel zones has no alarm
code assigned to it, and it will trigger an alarm, the activation of subsequent
detectors, which occur during the alarm, will be saved in the memory as zone
violation, not as alarm. If the system comprises any zones triggering an alarm of
which the monitoring station is not notified, it is necessary to enter the same
violation codes as for the alarms.
FS64 - programming zone RESTORE (end of violation) codes (HEX)
The codes programmed with this function are sent after the zone returns to its normal state
(according to the setting of corresponding zone options).
FS65 - programming zone TAMPER RESTORE codes (HEX)
The codes programmed with this function are sent after the tamper contact of the detector
connected to the 2EOL/NC and 2EOL/NO zones returns to its normal state.
FS67 - programming zone event assignment to station 1 (BIT)
FS68 - programming zone event assignment to station 2 (BIT)
The functions indicate which zone events are to be sent to station 1, and which to
station 2, if transmission to both stations has been selected in function FS47. The
programming consists in lighting up the LEDs to indicate the events (as per the list below)
and confirming the selection with the [#] key.
No. LED Option
ON
send „zone alarm” code
1
OFF
do not send „zone alarm” code
ON
send „zone tamper alarm" code
2
OFF
do not send „zone tamper alarm" code
ON
send „zone violation” code
4
OFF
do not send „zone violation” code
ON
send „zone restore” code
5
OFF
do not send „zone restore” code
ON
send „zone tamper restore” code
6
OFF
do not send „zone tamper restore” code
The state of LEDs 3, 7 and 8 is irrelevant.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's

Satel CA-6 Installatiehandleiding - English - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info