520094
66
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
Model menu
Aileron differential
FX-40
18.1 AILERON DIFFERENTIAL
Differential aileron travel is often required on fixed-wing model
air
craft in order to compensate for the phenomenon known as
adverse yaw. When the aeroplane is turning, the outboard
wing moves through the air more quickly, which means that
the drag generated by the down-going aileron (on the outside
of the turn) is greater than that of the up-going aileron. The
result is a yawing moment which tends to turn the model’s
nose away from the turn, swinging the model around its verti-
cal axis.
The effect of aileron differential is to reduce the travel of the
down-going aileron relative to that of the up-going aileron, with
the aim of generating equal amounts of drag on both wing
panels. This eliminates the adverse yaw problem.
This function acts as a mixer for two separate aileron servos,
enabling you to adjust travels for ‘aileron up’ and ‘aileron
down’ individually for each aileron. One of the auxiliary trans-
mitter controls can be set up as a means of fine-tuning the
degree of differential.
A separate
servo must be
used for each
control surface.
The FX-40 soft-
ware allows
you to assign
transmitter
controls in any
way you like.
The diagram above shows a typical fixed-wing model with two
ailerons on each wing panel.
Mark the ‘Aileron diff.’ option in the Model menu. The screen
now looks like this:
In our example the programming procedure is described for a
model with ‘only’ two aileron servos. Nevertheless, if you need
to activate this option for a complex model glider with up to
four ailerons, the set-up procedure is more or less identical.
Please follow the programming procedure described below:
Define the basic settings
In the ‘Glob’ field you can select ‘Sepa’ or ‘Glob’ modes;
the ef
fect has alr
eady been described, and is set using the
standard method.
Press the ‘Master’ field in the top right corner of the screen
to move on to the AFR and D/R settings for the ailerons.
The screen now looks like this:
The first step is to set the display mode in the ‘Display’ field;
you can define individually whether the screen is to show all
the flight modes (All modes), the currently active mode
(Separate) or the ‘AFR’ and ‘D/R’ settings.
The ‘Speed’ frame is used for adjusting servo transit speed.
You can enter a speed separately for the ‘there’ and ‘back’
directions, and the adjustment range is 0 to 27 increments.
Please note: the higher the number, the more slowly the
servo moves. The maximum value (27 increments) corres-
ponds to a duration of nine seconds. The default setting is
always ‘0’. When you mark one of the fields ‘there’ or
‘back’, the arrow button fields appear at the right margin. It
is possible to make adjustments in steps of one or ten
increments. Pressing the ‘Reset’ button restores the default
setting.
Pressing the ‘D/R’ button field displays the current Dual
Rate settings. Dual Rate values can be set at this point, in
parallel with the programming facilities which are described
in Section 17.2 on page 57.
Enter the dif
fer
ential travels
For the aileron servos (max. four) mark the appropriate
adjustment field for the left and right side. The arrow but-
tons are used to enter adjustments; note that you have to
move the stick to the right or left end-point in each case.
Adjustments can only be carried out for the side to which
the stick has been moved.
Set up a curve
It is possible to program a curve for the effect of the aileron
dif
fer
ential function. A percentage value can be entered in
addition to your preferred curve type for each side (Rate A
and Rate B). The values are adjusted exactly as described
for programming the Dual Rate curves; please refer to this
in Section 17.2 on page 58.
65
No differential
50% differential
100% differential (split mode)
Aileron 1
Aileron 3
Aileron 4
Aileron 2
66

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba FX-40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba FX-40 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robbe Futaba FX-40

Robbe Futaba FX-40 Gebruiksaanwijzing - Deutsch - 105 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info