779729

Prophete 0511 Handleiding

5
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
INSTRUCTION MANUAL
display to remind you of your bicycle inspection. Press the RIGHT key to switch off
this notice. After setting the inspection interval, the display will switch to the mode
for setting the time.
5.5 Setting the 12/24-hour display
Press and hold the LEFT key and the 24-hour display blinks. With the RIGHT key,
choose between the 12-hour and 24-hour display of the CLOCK and conrm
with the LEFT key.
5.6 Setting the clock
Immediately after choosing the 12/24-hour display you will be able to set the
time. The hours display ashes. Press the RIGHT key: The hours display is increased
by one. Press the LEFT key: The minutes display blinks. Press the RIGHT key: The
minutes display is increased by one. Press the LEFT key to conrm the time entry.
The settings are now completed and the bicycle computer is ready for use.
5.7 Bicycle computer check
To check if the bicycle computer and sensor were installed correctly, press the
LEFT key to activate the display. Place the computer in the computer mount and
turn the front wheel of your bicycle and the speed will be indicated.
5.8 New start/Reset
To reset entered and stored data, press both the LEFT and RIGHT keys at the
same time for approx. 3 seconds. All settings will have to be re-entered after the
new start/reset. (see Point 5.2 Setting the wheel size – 5.6 Setting the clock).
5.9 Automatic start/stop
Each time before the bicycle computer is used (display is blank), it must be
switched on by pressing a key. When you start off, all measurements begin auto-
matically until the bicycle stops. When you continue your ride, the measurements
continue. The bicycle computer switches off automatically to save the battery
after the bicycle has stopped moving for more than 5 minutes.
6. Modes/Functions
After starting up the bicycle computer, the display will show the speed and
the time.
Speed Is continuously calculated and updated and is ALWAYS displayed at the
top right. Measuring range: 0.1 – 99.9
Press the RIGHT key to switch between the following modes:
• ODO(totaldistancetravelled)
All travelled kilometres (miles) will be stored. Maximum memory range:
• DST(tripdistance)
Automatic start when bicycle trip begins. Maximum measuring range 999.9
• MXS(maximumspeed)
The maximum achieved speed is stored. Maximum measuring range: 99.9
• AVS(averagespeed)
Maximum measuring range: 99.9
• TM(triptime/tripchronometer)
Automatic start when bicycle trip begins. Maximum measuring range:
9 hrs 59 min 59 sec
• Temperature
Press and hold the LEFT key in the temperature mode: C (Celsius) blinks,
use the RIGHT key to now switch to F (Fahrenheit).
Conrm the desired setting with the LEFT key.
• SCAN(scanfunction)
Rolling display of functions: Continue pressing the RIGHT key until you reach
the SCAN mode. SCAN appears in the display. In this mode, the functions
(DST, MXS, AVS, TM) will be displayed automatically at 4-second intervals
in succession.
• One-timescanningquickrun-through
If you keep the RIGHT key pressed for approx. 2 seconds, a one-time scanning
quick run-through occurs.
• Time
Speed tendency and comparison is always displayed during the trip.
• Speedtendency
Display of current speed: The wheels of the bicycle symbol rotate faster
or slower.
• Speedcomparison
On the right next to the speed display you will see “+” or “-”.
This indicates that you are riding faster or slower than the previously travelled
average speed. (AVS)
• Instantaneousmemory
The bicycle computer has a unique instantaneous memory that can record
the values for trip distance (DST), average speed (AVS) and trip time (TM)
at the end of the driven distance. Press the LEFT key at the end of a stage.
The values for DST, AVS and TM are stored and can be reviewed at a later
period. You can view the saved values by repeatedly pressing the RIGHT key.
To exit this mode, press the LEFT key. The instantaneous memory is suitable
for, e.g. capturing data after a race to quickly save the values after crossing
the nish line.
6.1 Resettingtheroutedata(DST,TM,AVS)tozero
Press the RIGHT key to display (DST) and keep the LEFT key pressed for approx. 3
seconds. The three route data (trip distance counter – DST, trip time – TM, average
speed – AVS) will be reset to zero.
6.2 Resettingthemaximumspeed(MXS)tozero
Press the RIGHT key repeatedly until the maximum speed (MXS) is displayed
and hold down the LEFT key for 3 seconds. The maximum speed (MXS) is
reset to zero.
6.3 Manualentryoftotalkilometres
To enter the total kilometres (ODO) after battery replacement or new start/reset, all
of the settings from Point 5.2 Setting the wheel size to Point 5.6 Setting the clock
must be entered again.
Display is black
Too high temperature, or display is exposed to direct sunlight, will return to
normal after cooling off.
Display shows erratic numbers:
Remove the bicycle computer battery and reinsert.
No display
• Check the battery
• Is the battery inserted correctly? Observe +/-.
10. Warranty provisions
SI-Zweirad bicycle computer Art. No.: 0511
This bicycle computer has a 2-year warranty. Warranty begins as of the purchase
date (receipt, proof of purchase). During the warranty period, complaints about
defective bicycle computers can be made with your distributor, or at the service
address specied below. During this period we will correct free of charge all
defects that can be attributed to material defects or malfunctions. Excluded from
the warranty are batteries, improper handling, falls, impacts and the like. A new
warranty period does not begin after repairs or replacement of the device. The
warranty period of 2 years as of date of purchase remains denitive.
Please send your carefully packaged bicycle computer with your receipt to the
following address:
Prophete GmbH u. Co. KG
Lindenstrasse 50
33378 Rheda-Wiedenbrück
Phone: +49 (0) 5242 4108-59
Fax: +49 (0) 5242 4108-73
Email address: service@prophete.net
Website: www.prophete.de
5.2 Settingthewheelsize
After inserting new batteries (7.1), new start or change the wheel size.
C = Distance in millimetres per rotation
Determining the wheel size; mark the front wheel and the ground at the same
point, or use the valve as orientation. Move the wheel one wheel revolution
forwards and measure the covered distance in mm. This is your entry value.
Basic setting display: 2124 (=mm), The ones digit 4 blinks. Press the RIGHT key:
The ones digit is increased by one.
For all settings: Keep the RIGHT key pressed down – the respective numbers will
progress faster. Conrm your selection by pressing the LEFT key. The tens digit
now blinks. Press the RIGHT key: The tens digit is increased by one. Please set the
following digits in the same manner. The thousands digit can only be set from 0
to 5. Finally, press the LEFT key once more to conrm the setting.
5.3 SelectingKM/HMiles
The choice of the unit of measurement comes directly after entering the wheel
size. Press the RIGHT key to choose between KILOMETRE (KM) and MILES (M)
and conrm with the LEFT key. The system then switches to the mode to set the
inspection interval.
5.4 Settingtheinspectioninterval
The display 600 KM ashes. This function permits you to set the kilometres up
to the next bicycle inspection. Pressing the RIGHT key lets you make settings of
200/400/600 or 800 kilometres. Use the LEFT key to conrm the set value. After
the kilometres you set have been reached, a spanner symbol will appear in the
Then press the RIGHT key until you reach the mode (ODO). Now keep the LEFT key
pressed down for approx. 3 seconds, the last digit of the total kilometres begins
to blink. Press the RIGHT key to set the number and conrm the entry by pressing
the LEFT key. Then select the next digit for the entry. Repeat the procedure until the
desired value for the total kilometre counter has been set. Press the LEFT key again
to return to the normal (ODO) mode.
7. Battery replaceMent
7.1 Bicycle computer
Use a coin to unscrew the battery compartment lid at the back of the bicycle
computer. Insert the 3 V battery so that the positive pole (+) is visible. Replace the lid
and screw shut. After the batteries have been inserted, all settings must be re-entered
(see Point 5.2 Setting the wheel size).
F
8. declaration oF conForMity
We conrm that the bicycle computer conforms to the fundamental requirements
of the following European directives: the accordance of this product with the
directives is veried by the full compliance with the harmonised and non-
harmonised standards listed:
2004/108/EC EMC Directive
EN 61000-6-3:2001 (2007+A1:2011)
EN 61000-6-1 (2007)
9. description oF Fault
If a fault occurs, rst check the following points before submitting the bicycle
computer for complaint.
No speed indication:
• Check for correct magnet/sensor alignment.
• Check the batteries.
• If the battery is too weak, there will be no display.
Incorrect speed measurement or speed display at standstill, or high incorrect
maximum speed display
• Check if the wheel size was set correctly.
• Check if the correct KM/Miles setting is selected.
• Check if the magnet and sensor are positioned correctly.
• RF (radio frequency) interference from a chest strap. Do not get too close to
the bicycle computer with a chest strap, as the speed indicator will begin to
“run”.
• Unknown atmospheric or RF disturbances, atmospheric or radio interference,
high-voltage lines, railroad lines, etc. can also cause an incorrect speed
display.
Bicycle coMputer
OPERATING INSTRUCTIONS
Article no. 0511
15 functions
GB
BAFahrradPC0511_DE-FR-GB-IT-NL-HU-RO-PL.indb 1 11.11.2014 15:41:51
… 5 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Prophete 0511 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Prophete 0511 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 5.21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info