675037
8
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
POWX221 EN
Copyright © 2017 VARO P a g e | 8 www.varo.com
7.3 Assemble undercarriage Fig. G
Turn the machine upside down.
Remove the black plastic bottom plate by unscrewing the 6 screws. (Fig. G-1).
Unscrew the adjusting knob on the front and tilt the motor (Fig. G-2), then remove the
transport packing (Fig. G-3).
Now place one by one the uprights in the casing of the sawing bench (Fig. G-4).
Secure the uprights with 4 screws using a screwdriver, do not completely tighten the
screws (Fig. G-5).
Fit the 4 support bars, do not completely tighten the screws (Fig. G-6)
Fit the black plastic bottom plate and screw it tight.
Attach the rubber feet under the uprights (Fig. G-7).
Turn the machine into an upright position on a flat surface and adjust the machine so that
it stands in a stable position, tighten all the nuts and bolts (Fig. G-7).
7.4 Assemble bracket/push stick.
Attach the 2 brackets onto t he casing of the sawing bench and screw them tight (Fig. G-
8).
Place the push stick in the brackets.
7.5 Assembly and attachment of the rip fence Fig. D
Attach the aluminium fence (A) to the positioning block (B).
Now you can attach the complete rip fence to the bench top.
Slide the rip fence via one end of the positioning rail (C) over the bench top.
Adjust the position of the aluminium fence profile (A) such that the end corresponds to the
rear edge of the saw.
7.6 Assembly of the riving knife and the protective cap Fig. E
Turn the saw blade completely upwards.
Remove the bench inlay.
Assemble the riving knife on the set-up for this purpose and use hereby the Allen screws
and the filling rings. Ensure that the riving knife falls properly into the opening (= groove).
Now put the inlay back in the bench and fasten it.
Now assembly the protective cap onto the riving knife and use hereby the profiled nut and
self-locking nut.
Now lay a lath against the saw blade and the riving knife and check whether
it falls properly into the extension of the saw blade. If this is not the
case:Loosen the fastening bolts and place or remove the filling rings.
Above the saw table the radial distance between the riving knife and the toothed rim of the
saw blade shall not at any point exceed 5 mm at the depth of cut set.
The tip of the riving knife shall not be lower than 5 mm from the tooth peak, as shown.
7.7 Assembly of the saw blade
First remove the plug from the mains before the saw blade is assembled or
replaced.
Remove the inlay from the bench. Use a screwdriver for this purpose.
Turn the saw axle completely upwards. Remove the nut and the outside flange from the
saw axle.
Now slide the saw blade over the saw axle and now put the outside flange and the nut
back. Tighten the nut by hand.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX221 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX221 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX221

Powerplus POWX221 Gebruiksaanwijzing - Nederlands - 14 pagina's

Powerplus POWX221 Gebruiksaanwijzing - Deutsch - 15 pagina's

Powerplus POWX221 Gebruiksaanwijzing - Français - 14 pagina's

Powerplus POWX221 Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info