675037
7
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
POWX221 EN
Copyright © 2017 VARO P a g e | 7 www.varo.com
The handles for height and mitre setting of the saw blade are located in the transport
protection inside the machine.
Reassemble the bottom plate.
6.2 Switch off the machine immediately when you discover:
A defective mains plug or mains lead;
A defective switch.
Overheating of the machine.
Smoke or odeur caused by scorched insulation.
6.3 Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the wall outlet.
6.4 Using extension cables
As a supply for this machine always use an unloaded line and/or an extension cable with
conductors of at least 1,5 mm² and protected with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
Only connect your machine and/or extension cable to an earthed electricity mains.
This machine can be switched to the single phase network (230 V/50 Hz). If you are in
doubt about the earth of the electricity provisions, consult an electrician first.
7 ASSEMBLY
7.1 Assembly of the bench extensions Fig. F
Before attaching the bench extensions, first remove the perforated base plate (you can
now also remove and discard the motor protection materials).
Once the bottom side is open, you can attach the diagonal support struts to the bench
saw.
Now attach the bench extensions to the basic bench top. Next, attach the extensions to
the diagonal support struts.
Once all the extensions have been assembled, re-attach the base plate (taking care that
all extensions are perfectly lined up with the basic bench top itself).
Lastly, attach the guide rail (with ruler) to the front edge of the bench top.
7.2 Assembly of the bench saw on the workbench Fig. B & C
Before adjusting the saw, make sure the plug is removed from the socket.
Fig. B shows the distance of the holes to be drilled in the workbench on which to fasten the
machine. Drill holes of 8 mm.
Only use the machine after it has been assembled completely and it has
been screwed onto the workbench or the frame.
Fig. C shows the part to be sawn out (310 x 310 mm), so that the sawdust can fall through
it and piling up is prevented!
Only if you do not use an extraction system!
Fasten the machine with bolts.
If the frame is used, it must be fixed on the floor with four screws and the machine must be
fixed on the frame with four screws. Check the screws before switching the machine on.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX221 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX221 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Powerplus POWX221

Powerplus POWX221 Gebruiksaanwijzing - Nederlands - 14 pagina's

Powerplus POWX221 Gebruiksaanwijzing - Deutsch - 15 pagina's

Powerplus POWX221 Gebruiksaanwijzing - Français - 14 pagina's

Powerplus POWX221 Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info