629274
30
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
30 © 2015 UTC Fire & Security Americas Corporation, Inc. All rights reserved.
No Jumper (Dry Contact Switching)
Dry contact closure provided to output terminal. Maximum Load 30 VAC @ 1 A or
24 VDC @ 1 A. DO NOT exceed these ratings.
Jumper between GND and C (Negative Switching)
Bus Ground provided to output terminal @ typical 0V. Do not exceed relay rating
which is maximum load 30 VAC @ 1 A or 24 VDC @ 1 A.
Jumper between C and 12 V + (Positive Switching)
Bus Voltage provided to output terminal @ typical 12-13 VDC. Maximum Load @
12 V is total panel current; this includes all connected keypads and expansion
modules. Consult your panel’s specifications for maximum current rating. Do not
exceed relay current rating of 1A.
Caution: Do not exceed the Maximum Load ratings above for the relay
configuration. Exceeding the maximum rating could result in possible damage to the
product.
WARNING: DO NOT CONNECT MAINS VOLTAGE TO THE NX-595E. DOING SO
COULD DAMAGE THE MODULE OR NETWORX PANEL AND POSE AN
ELECTRICAL HAZARD THAT COULD RESULT IN A FIRE OR CAUSE SERIOUS
ELECTRICAL SHOCK OR LOSS OF LIFE.
Current Limit Caution: Check the current requirements of your load before
connecting! There is no overcurrent protection on the relays when providing bus
ground or bus voltage (jumper between GND and C, or C and 12 V +). You must
ensure your load does not exceed the recommended limits above. Exceeding limits
can damage the module. NetworX panels do have overcurrent protection on the
bus and may disconnect the bus to provide temporary protection. If enabled, your
panel will report "Overcurrent Fault" or "Expander Overcurrent". Repeated
overcurrent conditions can result in permanent damage to the panel or connected
devices.
Advanced Network Setup
If the IP address is empty (Location 21, Segment 1 will be 0 in the NetworX panel),
then you will have to manually program the network settings into the NX-595E. This
is an unlikely scenario as most routers are configured to automatically assign
network settings with DHCP. Before you manually configure the NX-595E, verify
with the network administrator or home owner that they have disabled DCHP in the
router. You will need the following settings from the network administrator or home
owner if they have DHCP disabled:
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NetworX NX-595E IP Communication Module bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NetworX NX-595E IP Communication Module in de taal/talen: Engels als bijlage per email.

De handleiding is 0,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info