493509
8
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
10 REMOTE SENSOR: Point the SR 8 remote control at the remote
sensor and press the buttons. Do not expose the remote sensor of the
C 725BEE to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the C 725BEE with the
remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30o in each direction of the front of the remote sensor.
11 RECORD OUT/ZONE 2 SELECTOR: This knob doubles as both a record
and zone source selector. Rotate knob and select the Source you would
like to be directed out to REC OUT/ZONE 2 output port in the rear panel.
The directed Source signal at the REC OUT/ZONE 2 output port could
be used for making audio recordings or as an audio input to a separate
zone in your home.
ABOUT ZONE FEATURE
The Zone feature allows one to simultaneously listen to another active
Source of the C 725BEE that is dierent from the currently selected Source.
For example, while the C 725BEE is at CD mode, you can set the RECORD
OUT/ZONE 2 SELECTOR knob to TUNER” and the active tuned stations
audio will be directed to REC OUT/ZONE 2 output port in the rear panel.
You can then feed the REC OUT/ZONE 2 jack to another amplier or receiver
that is located maybe in another area of your home or building. With your
separate amplier or receiver selecting the fed signal and with speakers
connected, you can then enjoy listening to the tuned station. You can
vary the level of the tuned station by adjusting the Volume control of the
separate amplier or receiver. Refer also to the item USING THE
ZR 5 REMOTE CONTROL at the REMOTE CONTROL section of the
the IDENTIFICATION OF CONTROLS page.
12 VOLUME: The VOLUME control adjusts the overall loudness of the signals
being fed to the loudspeakers or headphones. Turn clockwise to increase
the volume setting; counter clockwise to lower it. The VOLUME control does
not aect recordings made using the REC OUT/ZONE 2 output but will
aect the signal going to the Pre-amp output (PRE OUT).
NOTE
If the Volume level is adjusted using the SR 8’s [VOL ] buttons, the
lower line of the VFD will show “Volume Up” when level is increased or
Volume Down” if level is decreased.
13 PHONES: A 1/4” stereo jack socket is supplied for headphone listening
and will work with conventional headphones of any impedance. The
headphone socket will work in parallel to the selected speakers. To
listen to headphones only, de-select Speakers A and/or B. The volume,
tone and balance controls are operative for headphone listening. Use
a suitable adapter to connect headphones with other types of sockets,
such as 3.5mm “personal stereo” jack plugs.
NOTE
Make certain that the volume control is turned to minimum (fully
counter-clockwise) before connecting or disconnecting headphones.
Listening at high levels can damage your hearing.
14 A SPEAKERS B: The SPEAKERS A and B buttons engage or disengage
the speakers connected respectively to the SPEAKERS A and SPEAKERS
B terminals on the rear panel. Press A to switch ON or OFF the speakers
connected to the SPEAKERS A terminals. Press “B to switch ON or OFF
the speakers connected to the SPEAKERS B terminals.
15 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the
audio output of a Media Player. The LED on the MP input button will
illuminate when an external Media Player is connected to this socket.
16 INPUT SELECTORS: These buttons select the active input to the NAD
C 725BEE and the signal sent to the loudspeakers, headphones and the
PRE OUT socket. The buttons on the remote control handset duplicate
these buttons. The selected input will be displayed in the VFD.
MP (MEDIA PLAYER): Selects a line-level source connected to the MP
sockets as the active input. If the DATA port of the optional NAD IPD 1
Dock with iPod (NAD IPD 1) is connected to the corresponding DATA
PORT in the rear panel, your iPod player docked and with the NAD IPD
1’s AUDIO OUT also connected to the rear panel MP input, the lower
line of the VFD will show “iPod Connected”. Refer also to LISTENING TO
YOUR iPod PLAYER under the OPERATION main heading.
If an external Media Player is connected to the front MP socket (using
a 3.5mm stereo plug) while listening to a MP line-level source, the
external Media Player will be directly selected with the MP line-level
source immediately disconnected. It is recommended to mute the
volume or switch to a dierent input before plugging/unplugging the
external Media Player cable.
CD: Selects the CD (or other line-level source) connected to the CD
sockets as the active input.
TUNER: Toggle to select AM, FM or DAB (230V version only) tuner band.
DISC: Selects a line-level source connected to the DISC sockets as the
active input.
AUX: Selects a line-level source connected to the AUX sockets as the
active input.
TAPE: Selects the Tape (or other line-level source) connected to the
TAPE sockets as the active input.
17 TONE DEFEAT: Tone Controls are enabled or disabled by pressing this
button. The lower line of the VFD will show Tone Defeat when the tone
controls are bypassed or Tone Active” if the tone controls are enabled.
18 TONE CONTROLS: The NAD C 725BEE is tted with BASS and TREBLE
tone controls to adjust the tonal balance of your system. The 12 oclock
position is “at with no boost or cut, and an indent indicates this
position. Rotate the control clockwise to increase the amount of Bass or
Treble. Rotate the control counterclockwise to decrease the amount of
Bass or Treble. The Tone controls do not aect recordings made using
the REC OUT/ZONE 2 output but will aect the signal going to the Pre-
amp output (PRE OUT).
19 BALANCE: The BALANCE control adjusts the relative levels of the left
and right speakers. The 12 o’clock position provides equal level to the
left and right channels. A detent indicates this position. Rotating the
control clockwise moves the balance towards the right. Rotating the
control counterclockwise moves the balance to the left. The BALANCE
control does not aect recordings made using the REC OUT/ZONE
2 output but will aect the signal going to the Pre-amp output (PRE
OUT).
IDENTIFICATION OF CONTROLS
FRONT PANEL
8
ENGLISH FRAAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD C 725 BEE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD C 725 BEE in de taal/talen: Engels als bijlage per email.

De handleiding is 1,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van NAD C 725 BEE

NAD C 725 BEE Gebruiksaanwijzing - Nederlands - 24 pagina's

NAD C 725 BEE Gebruiksaanwijzing - Deutsch - 24 pagina's

NAD C 725 BEE Gebruiksaanwijzing - Français - 24 pagina's

NAD C 725 BEE Gebruiksaanwijzing - Espanõl - 24 pagina's

NAD C 725 BEE Gebruiksaanwijzing - Svenska - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info