738663
43
Verklein
Vergroot
Pagina terug
1/146
Pagina verder
Advanced operations 15
7 Advanced operations
In this section we’ll describe some advanced operations which you can
do with your handheld transceiver.
7.1 Channel Scanning
If you have more than one channel programmed, your ALAN
HP106/HP406 can scan them; in other words it can repeatedly switch
through all the programmed channels cyclically and automatically stop
when a signal is detected on one of them. During the scanning, only the
channels belonging to a specific scanning list (defined by the set-up) are
monitored. If a valid signal is received during the scanning, the scanning
stops and the communication is audible through the speaker. When the
signal is over, the scanning automatically restarts.
If the CTCSS/DCS or the selective call have been previously program-
med, the device could be set-up to stop only if the received signals con-
tain the correct signaling.
7.1.a Enabling/disabling scanning
To enable the scanning:
1) Turn off the device
2) Turn on the device keeping the MON + FUNC button pressed. A high
beep (after the acoustic tone of power-on confirmation stated in the
paragraph 5.1) notifies that the scanning is activated, and the status
LED will slowly blink amber.
During scanning the channel selector knob becomes invalid.
If the Scan List is empty, an error tone will be heard when you try to
activate the scan and the radio will not start the Scan Mode.
Obviously, at least two channels must be entered in the Scan List for
the unit to be put in the SCAN Mode.
If the PTT button is pressed during the channel scanning, this one will
stop and the radio will transmit on the first vacant channel, then the
unit will automatically resume scanning.
To stop the scanning, repeat the above procedure from step 1. A low
beep is produced and the scanning will stop.
7.1.b Priority Channel
Depending on the transceiver’s programming, one of the scanning list
channels could have been assigned as Priority Channel. The scanning
will monitor the priority channel more frequently.
The programming could has been also set-up to allow you to decide,
from time to time, which is the channel to assign as priority. For informa-
tion please contact your dealer/radio network manager.
To assign a priority channel (if previously enabled by the programming):
1) Ensure that the scanning is not active.
2) Before starting the scan mode, select the desired channel using the
channel selector.
3) Start the channel scanning as described in paragraph 7.1.a. The
channel previously selected by the channel selector will be scanned
more frequently.
Once the scanning is started, if you wish to change the priority chan-
nel, you need to disable the scanning. Therefore it is not sufficient to
turn-off the device, rotate the channel selector, and switch it on again.
Depending on the programming, on the priority channel could also be
set the busy channel lock out function (BCLO) or other conditions (i.e.
English
ISTR106_int 26-09-2003 9:47 Pagina 15
43

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midland Alan HP 406 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midland Alan HP 406 in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info