595375
16
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
16
ENGLISH
ENG
23 Adjusting screw (adjust saw blade angle)
24 Lock nut (adjust saw blade angle)
25 Hexagon spanner
26 Locking screw (
for setting cutting depth
)
27 Scale (depth of cut)
28 Spindle locking button
* equipment-dependent
Metabo S-automatic safety clutch:
If the tool jams or catches, the power supply to
the motor is restricted. Due to the strong force
which can arise, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Mechanical safety brake for stopping saw blade
quickly when switching off the machine (KSE 68
Plus only).
Hard-wearing guide plate made from light-
weight cast magnesium
Vibration-damping, non-slip rubber coating in
grip area.
Double-guided parallel stop, can be used on the
left and right for greater flexibility
Lock preventing inadvertent machine start-up
Lubricating system extends the service life of
the gearbox
Vario Tacho Constamatic (VTC) full-wave elec-
tronics for stepless speed adjustment. The
machine speed stays constant automatically
under load (only KSE 68 Plus)
Setting wheel for speed preselection (only KSE
68 Plus)
Electronic function monitoring the coil tempera-
ture protects against overload. Light signal
when the machine begins to overload (only KSE
68 Plus)
External dust extraction possible: option of
connecting an extraction unit
Carbon brushes for protecting the motor
Guide rail available as an accessory (order no.
6.31213)
Tool-less fine machine adjustment when used
on guide rail 6.31213
Before plugging in, check to see that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Pull the plug out of the plug socket before
any adjustments or servicing are performed.
7.1 Setting splitting wedge
The splitting wedge (16) prevents the wood from
closing behind the saw blade and jamming it while
the machine is in operation. This could otherwise
lead to recoiling.
The splitting wedge must be set in such a
way that the distance between its inner curve
and the toothed ring on the saw blade is no greater
than 5 mm. Set the splitting wedge so that the
lowest point of the saw blade does not protrude by
more than 5 mm below the bottom edge of the
splitting wedge. See illustration on page 2.
To adjust, loosen the hex screw (15), set the right
distances to the saw disc and tighten the hex
screw again.
7.2 Setting depth of cut
Loosen the locking screw (26). Raise or lower the
motor section against the guide plate (1). Read the
depth of cut that has been set from the scale (27).
Tighten the locking (26)screw again.
It is advisable to set the depth of cut in such a way
that no more than half of each tooth on the saw
blade juts out under the workpiece. See illustration
on page 3.
The clamping power of the locking screw (26) can
be adjusted. Unscrew the screw on the lever to do
this. Remove lever and mount offset anticlockwise.
Secure with screw. When doing this, note that the
cutting depth setting device moves freely when the
lever is open.
7.3 Slanting saw blade for diagonal cuts
Loosen the two locking screws (6) to make the
setting. Tilt the motor section against the guide
plate. Read the angle which has been set from the
scale (4). Retighten the front and then the rear
locking screw (6).
7.4 Correcting the saw blade angle
The
saw blade angle is set ex works.
If, at 0°, the saw blade is not at right angles to the
guide plate: release locking screws (6). Release
lock nut (24) and correct saw blade angle with
adjusting screw (23). Then retighten the lock nut.
Retighten both locking screws (6).
7.5 Rotational speed preselection
Select the speed at the setting wheel (14). For
recommended speeds, see page 2.
6 Special Product Features
7 Initial Operation, Setting
17026944_0209 KSE 6x Plus MG-Guss.book Seite 16 Montag, 26. Januar 2009 2:08 14
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo KS Plus PartnerEdition bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo KS Plus PartnerEdition in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info