691782
25
Verklein
Vergroot
Pagina terug
1/244
Pagina verder
25 ENGLISH
Laser line can be shifted to either the left or right side of
thesawbladebyturningtheadjustingscrewasfollows.
►Fig.30: 1.Adjustingscrew
1. Loosentheadjustingscrewbyturningit
counterclockwise.
2. Withtheadjustingscrewloosened,slidethe
adjustingscrewtotherightorleftasfarasitgoes.
3. Tightentheadjustingscrewrmlyattheposition
where it stops sliding.
NOTE:Laserlineisfactoryadjustedsothatitisposi-
tioned within 1 mm from the side surface of the blade
(cutting position).
NOTE: When laser line appears dim and hard to see
because of direct sunlight, relocate the work area to a
place where there is less direct sunlight.
Aligning the laser line
Alignthecuttinglineonyourworkpiecewiththelaserline.
►Fig.31
A)Whenyouwanttoobtainthecorrectsizeontheleft
side of workpiece, shift the laser line to the left of the
blade.
B) When you want to obtain the correct size on the right
side of workpiece, shift the laser line to the right of the
blade.
NOTE: Use wood facing against the guide fence
when aligning the cutting line with the laser line at the
side of guide fence in compound cutting (bevel angle
45° and miter angle right 45°).
ASSEMBLY
WARNING: Always be sure that the tool is
switched off and the battery cartridge is removed
before working on the tool. Failure to switch off and
remove the battery cartridge may result in serious
personalinjury.
Hex wrench storage
When not in use, store the hex wrench as shown in the
guretokeepitfrombeinglost.
►Fig.32: 1. Hex wrench
Removing and installing saw blade
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before installing or removing the blade.Accidental
startupofthetoolmayresultinseriouspersonalinjury.
WARNING:
Use only the Makita wrench pro-
vided to install or remove the blade. Failure to use the
wrenchmayresultinovertighteningorinsufcienttight-
eningofthehexsocketboltandseriouspersonalinjury.
Alwayslockthecarriagewithraisedpositionwhen
removing and installing the blade. Pull the stopper pin
and rotate it 90° with the carriage raised.
►Fig.33: 1. Unlocked position 2. Locked position
3. Stopper pin
Removing the blade
Loosen the hex bolt holding the center cover using the
hex wrench. Raise the blade guard and center cover.
►Fig.34:
1. Center cover 2. Hex wrench 3. Blade guard
Press the shaft lock to lock the spindle and use the hex
wrenchtoloosenthehexsocketbolt.Thenremovethe
hexsocketbolt,outerangeandblade.
►Fig.35: 1. Shaft lock 2. Hex wrench 3. Hex socket
bolt (left-handed) 4. Loosen 5.Tighten
Installing the blade
Mount the blade carefully onto the spindle, making sure
that the direction of the arrow on the surface of the blade
matches the direction of the arrow on the blade case.
►Fig.36: 1.Arrowonthebladecase2.Arrowonthe
blade
Installtheouterangeandhexsocketbolt.Tightenthe
hex socket bolt counterclockwise using the hex wrench
while pressing the shaft lock.
►Fig.37: 1. Hex socket bolt 2.Outerange3. Saw
blade 4.Innerange5. Spindle 6. Ring
NOTICE:Iftheinnerangeisremoved,besureto
install it on the spindle with its protrusion facing away
fromtheblade.Iftheangeisinstalledincorrectly,the
angewillrubagainstthemachine.
Return the blade guard and center cover to its original
position.Thentightenthehexboltclockwisetosecure
the center cover. Unlock the stopper pin to release
carriage from the raised position. Lower the handle to
make sure that the blade guard moves properly. Make
sure shaft lock has released spindle before making cut.
WARNING: Before mounting the blade onto
the spindle, always be sure that the correct ring
for the blade's arbor hole you intend to use is
installed between the inner and the outer anges.
Use of the incorrect arbor hole ring may result in the
improper mounting of the blade causing blade move-
ment and severe vibration resulting in possible loss
of control during operation and in serious personal
injury.
Connecting a vacuum cleaner
When you wish to perform clean cutting operation, con-
nect a Makita vacuum cleaner to the dust nozzle using
a front cuff 24 (optional accessory).
►Fig.38: 1. Front cuff 24 2. Hose 3. Vacuum cleaner
Dust bag
Theuseofthedustbagmakescuttingoperationscleanand
dustcollectioneasy.Toattachthedustbag,removethe
dust extraction hose on the tool and connect the dust bag.
►Fig.39: 1. Dust extraction hose 2. Dust bag
When the dust bag is about half full, remove the dust
bag from the tool and pull the fastener out. Empty
the dust bag of its contents, tapping it lightly so as to
remove particles adhering to the insides which might
hamper further collection.
►Fig.40: 1. Fastener
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS111 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 37,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info