691782
23
Verklein
Vergroot
Pagina terug
1/244
Pagina verder
23 ENGLISH
In the interest of your personal safety, always maintain
thebladeguardingoodcondition.Anyirregularopera-
tion of the blade guard should be corrected immediately.
Check to assure spring loaded return action of guard.
WARNING: Never use the tool if the blade
guard or spring are damaged, faulty or removed.
Operation of the tool with a damaged, faulty or
removedguardmayresultinseriouspersonalinjury.
If the see-through blade guard becomes dirty, or saw-
dustadherestoitinsuchawaythatthebladeand/or
workpiece is no longer easily visible, remove the bat-
teries and clean the guard carefully with a damp cloth.
Do not use solvents or any petroleum-based cleaners
on the plastic guard because this may cause damage
to the guard.
If the blade guard is especially dirty and vision through
the guard is impaired, remove the batteries and use the
supplied wrench to loosen the hex bolt holding the cen-
ter cover. Loosen the hex bolt by turning it counterclock-
wise and raise the blade guard and center cover. With
the blade guard so positioned, cleaning can be more
completelyandefcientlyaccomplished.Whencleaning
is complete, reverse procedure above and secure bolt.
Do not remove spring holding blade guard. If guard
becomes discolored through age or UV light exposure,
contact a Makita service center for a new guard. DO
NOTDEFEATORREMOVEGUARD.
►Fig.13: 1. Center cover 2. Hex wrench 3. Blade
guard
Kerf boards
Thistoolisprovidedwiththekerfboardsintheturn
basetominimizetearingontheexitsideofacut.The
kerfboardsarefactoryadjustedsothatthesawblade
doesnotcontactthekerfboards.Beforeuse,adjustthe
kerf boards as follows:
►Fig.14: 1. Kerf board
►Fig.15: 1. Left bevel cut 2. Straight cut 3. Right
bevel cut 4. Saw blade 5. Blade teeth
6. Kerf board
First, remove the batteries. Loosen all the screws (2
each on left and right) securing the kerf boards until the
kerf boards can still be easily moved by hand. Lower the
handle fully, then pull and turn the stopper pin to lock
the handle in the lowered position. Release the stopper
pin on the sliding pole and pull the carriage toward you
fully.Adjustthekerfboardssothatthekerfboardsjust
contactthesidesofthebladeteeth.Tightenthefront
screws(donottightenrmly).Pushthecarriagetoward
theguidefencefullyandadjustthekerfboardssothat
thekerfboardsjustcontactthesidesofbladeteeth.
Tightentherearscrews(donottightenrmly).
Afteradjustingthekerfboards,releasethestopper
pinandraisethehandle.Thentightenallthescrews
securely.
NOTICE: After setting the bevel angle ensure
that the kerf boards are adjusted properly. Correct
adjustmentofthekerfboardswillhelpprovideproper
support of the workpiece minimizing workpiece tear
out.
Maintaining maximum cutting
capacity
Thistoolisfactoryadjustedtoprovidethemaximum
cutting capacity for a 260 mm saw blade.
When installing a new blade, always check the lower
limitpositionofthebladeandifnecessary,adjustitas
follows:
First,removethebatteries.Turnthestopperleverto
engaged position.
►Fig.16: 1. Stopper lever
Push the carriage toward the guide fence fully and
lower the handle completely.
Adjustthebladepositionbyturningtheadjustingbolt
withthehexwrench.Theperipheryofthebladeshould
extend slightly below the top surface of the turn base
and also comes to the point where the front face of the
guide fence meets the top surface of the turn base.
►Fig.17: 1.Adjustingbolt
►Fig.18: 1.Topsurfaceofturnbase2. Periphery of
blade 3. Guide fence
With the batteries removed, rotate the blade by hand
while holding the handle all the way down to be sure
that the blade does not contact any part of the lower
base.Re-adjustslightly,ifnecessary.
Afteradjustment,alwaysreturnthestopperlevertothe
original position.
WARNING: After installing a new blade and
with the batteries removed, always be sure that
the blade does not contact any part of the lower
base when the handle is lowered completely. If
a blade makes contact with the base it may cause
kickbackandresultinseriouspersonalinjury.
Stopper arm
Thelowerlimitpositionofthebladecanbeeasily
adjustedwiththestopperarm.Toadjustit,turnthe
stopper arm in the direction of the arrow as shown in the
gure.Turntheadjustingscrewsothatthebladestops
at the desired position when lowering the handle fully.
►Fig.19: 1. Stopper arm 2.Adjustingscrew
Adjusting the miter angle
CAUTION: After changing the miter angle,
always secure the turn base by tightening the grip
rmly.
NOTICE: When turning the turn base, be sure to
raise the handle fully.
►Fig.20: 1. Lock lever 2. Grip 3. Releasing lever
4. Pointer
Rotate the grip counterclockwise to unlock the turn
base.Turnthegripwhileholdingdownthelockleverto
movetheturnbase.Alignthepointerwithyourdesired
angle on the scale then tighten the grip.
NOTE: If you depress the releasing lever, you can
move the turn base without holding down the lock
lever.Tightenthegripatyourdesiredposition.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS111 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 37,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info