691782
26
Verklein
Vergroot
Pagina terug
1/244
Pagina verder
26 ENGLISH
Securing workpiece
WARNING: It is extremely important to always
secure the workpiece correctly with the proper
type of vise or crown molding stoppers. Failure to
dosomayresultinseriouspersonalinjuryandcause
damagetothetooland/ortheworkpiece.
WARNING: After a cutting operation do not
raise the blade until it has come to a complete
stop.Theraisingofacoastingblademayresultin
seriouspersonalinjuryanddamagetotheworkpiece.
WARNING: When cutting a workpiece that
is longer than the support base of the saw, the
material should be supported the entire length
beyond the support base and at the same height
to keep the material level. Proper workpiece support
will help avoid blade pinch and possible kickback
whichmayresultinseriouspersonalinjury.Donot
relysolelyontheverticalviseand/orhorizontalvise
tosecuretheworkpiece.Thinmaterialtendstosag.
Support workpiece over its entire length to avoid
bladepinchandpossibleKICKBACK.
►Fig.41: 1. Support 2.Turnbase
Guide fences
WARNING: Before operating the tool, make
sure that the upper fence is secured rmly.
WARNING: Before bevel-cutting, make sure
that no part of the tool, especially the blade, con-
tacts the upper and lower fences when fully low-
ering and raising the handle in any position and
while moving the carriage through its full range
of travel. If the tool or blade makes contact with
the fence this may result in kickback or unexpected
movementofthematerialandseriouspersonalinjury.
Use upper fences to support the material higher than
the lower fences. Insert the upper fence into the hole on
the lower fence and tighten the clamping screw.
►Fig.42: 1. Upper fence 2. Lower fence 3. Clamping
screw 4.Adjustingscrew
NOTICE:Thelowerfencesarexedtothebasein
the factory. Do not remove the lower fences.
NOTICE: If the upper fence is still loose after tight-
eningtheclampingscrew,turntheadjustingscrewto
closeagap.Theadjustingscrewisfactoryadjusted.
Youdon'tneedtouseitunlessneeded.
Youcanstoretheupperfencesontotheholderwhen
not in use. Use the clip on the upper fence to hold it on
the holder.
►Fig.43: 1. Holder 2. Upper fence 3. Clip
Vertical vise
WARNING: The workpiece must be secured
rmly against the turn base and guide fence with
the vise during all operations. If the workpiece is
not properly secured against the fence the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
personalinjury.
►Fig.44: 1. Vise arm 2. Vise rod 3. Clamping screw
4. Vise knob
Theverticalvisecanbeinstalledintwopositionson
either the left or right side of the base. Insert the vise
rod into the hole in the base.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. If the clamping screw contacts
the carriage, install it on the opposite side of vise arm.
Make sure that no part of the tool contacts the vise
when lowering the handle all the way. If some part
contacts the vise, re-position the vise.
Presstheworkpieceatagainsttheguidefenceandthe
turn base. Position the workpiece at the desired cutting
positionandsecureitrmlybytighteningtheviseknob.
NOTE:Foraquicksettingofworkpiece,turningthe
vise knob to 90° counterclockwise allows the vise
knobtobemovedupanddown.Tosecurethework-
piece after setting, turn the vise knob clockwise.
Horizontal vise
Optional accessory
WARNING: Always rotate the vise nut clock-
wise until the workpiece is properly secured. If
the workpiece is not properly secured the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
personalinjury.
WARNING: When cutting a thin workpiece,
such as base boards, against the fence, always
use the horizontal vise.
Thehorizontalvisecanbeinstalledintwopositionson
either the left or right side of the base. When performing
22.5° or greater miter cuts, install the horizontal vise on
the side opposite the direction in which the turn base is
to be turned.
►Fig.45: 1. Vise plate 2. Vise nut 3. Vise knob
Byippingthevisenutcounterclockwise,theviseis
released,andrapidlymovesinandout.Togripthe
workpiece, push the vise knob forward until the vise
platecontactstheworkpieceandipthevisenutclock-
wise.Thenturntheviseknobclockwisetosecurethe
workpiece.
NOTE:Themaximumwidthofworkpiecewhichcan
be secured by the horizontal vise is 228 mm.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS111 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 37,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info