683161
171
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Controlling the Linear Amplifier
This section describes the procedures for configuring the control
signal and TX/RX delay when using a linear amplifier.
Outputs of the mechanical relay (MKE, BRK, COM) and
semiconductor switch (RL) are output to the REMOTE connector
on the rear panel, which allows users to combine the use of this
transceiver with their linear amplifier.
The control signal status and whether to enable TX delay time can
be configured on the menu screen.
HF band, 50 MHz band and 70 MHz band (E type only) can be
configured separately.
Connection
Use the supplied 7-pin DIN plug to make your own connection
cable.
TL-922 Connection
Connect terminal no. 2 (COM) of the REMOTE connector to GND
of TL-922, and terminal no.4 (MKE) of the REMOTE connector to
RL CONT of TL-922. Connect terminal No. 6 (ALC) of the
REMOTE connector to ALC OUT of TL-922.
.
TS-890S
TL-922
2
4
1
67
3
5
ALC
GND
RL CONT
GND
COM
MKE
REMOTE Connector
(View from Rear Panel)
7-pin DIN Plug
General Linear Amplifier Connection
Follow the diagram below to connect a commercially available
linear amplifier.
The ALC circuit of this transceiver starts to operate from an ALC
output voltage of approximately -4 V (which can be changed
from the Linear Amplifier menu) from the linear amplifier. To
enhance the stability of the output and ALC operation, it is
recommended that the TX output power limiter function be
configured.
For more details on connection with a linear amplifier, please
refer to the instruction manual of the linear amplifier to be used.
.
TS-890S
2
4
1
67
3
5
ALC
GND
(RX)
(TX)
COM
BRK
LKY
MKE
10Ȑ
10Ȑ
ON during Active Low/transmission: “L”
ON during Active High/transmission: 12 V
REMOTE Connector
(View from Rear Panel)
Linear Amplifier
(Commercially
Available)
7-pin DIN Plug
Connect to either ANT 1 or 2.
AC100~240V
50/60Hz
GND
RF INPUT
RF OUT
ALC
TX
Control
The method for controlling linear amplifiers varies with
the type of linear amplifier in use. There are some linear
amplifiers that place this transceiver in the TX mode once
the control terminal is connected to GND. When using
such types of linear amplifiers, connect terminal no. 2
(COM) of the REMOTE connector to GND of the linear
amplifier, and terminal no. 4 (MKE) of the REMOTE
connector to the control terminal of the linear amplifier.
OTHER FUNCTIONS 16
16-13
171

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info