683161
170
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Control of External Devices
TX Inhibit in Busy State (when Squelch is Open)
When transmission is inhibited in the busy state, pressing [SEND]
on the front panel or [PTT] on the microphone does not execute
transmission while this transceiver is busy.
Configure in Advanced Menu [12] TX Inhibit While
Busy
Setting Value Off (default)/ On
Reversing the PKS Signal Polarity
Short-circuiting the PKS terminal to GND places this transceiver
in the TX mode. This polarity can be reversed according to the
device to be connected.
Configure in Advanced Menu [11] PKS Polarity
Reverse
Setting Value Off (default)/ On
Off: Short-circuiting the PKS terminal of the ACC 2 connector
to GND places this transceiver in the TX mode.
On: Applying a voltage of 3 V to 5 V to the PKS terminal of the
ACC 2 connector places this transceiver in the TX mode.
USB Keying
This function is compatible with PC applications for controlling the
different behaviors including CW keying, RTTY frequency shift and
PTT/SEND (TX/RX switching) using the RTS/DTR signal of the
COM port.
It allows the above behaviors to be assigned to the RTS and DTR
signals of the 2 virtual COM ports (Standard and Enhanced) during
USB connection.
Off: Disabled
Flow Control: Behaves as a hardware flow control signal for
command communication.
CW Keying: Behaves as a CW keying signal.
RTTY Keying: Behaves as an RTTY frequency shift key signal.
PTT: Behaves in the same way as PTT (SEND).
DATA SEND: Behaves in the same way as DATA SEND (PKS).
Configure in Advanced Menu [17]
Virtual Standard
COM Port – RTS
Setting Value
Flow Control (default)/ CW Keying/ RTTY
Keying/ PTT/ DATA SEND
Configure in Advanced Menu [18] Virtual Standard
COM Port – DTR, [19] Virtual Enhanced COM Port
– RTS or [20] Virtual Enhanced COM Port – DTR
Setting Value
Off (default)/ CW Keying/ RTTY Keying/ PTT/
DATA SEND
To switch the COM port or exit the application in the PC
application for performing transmission on the
transceiver using the USB keying function, be sure to
complete the transmission before doing so. Otherwise
transmission error may occur on the transceiver.
If the COM port for outputting the USB keying signal is
not selected (open) in the PC application that is using the
USB keying function, the signal for USB keying may be
accidentally transmitted. Press [
] to turn off the power
of this transceiver or disable the USB keying function
temporarily until the preparation on the PC application is
completed.
“RTTY Keying” can only be configured for 1 out of the 4
signals (duplicate configuration is not allowed).
When this menu is configured to “RTTY Keying” (during
RTTY operation via USB keying), RTK of the ACC 2
connector will be disabled.
Please use the latest virtual COM port driver.
Decoded Character Output
This function outputs characters decoded by the built-in decoder
of CW/ RTTY/ PSK from the virtual COM port (Enhanced). The
baud rate is also variable.
Turning ON/OFF Decoded Character Output
Configure in Menu [7-03]
Decoded Character
Output
Setting Value Off (default)/ On
Configuring the Baud Rate of the Virtual COM
(Enhanced) Connector
Configure in Menu [7-02]
Baud Rate (Virtual
Enhanced COM)
Setting Value
9600/ 19200/ 38400/ 57600/ 115200 (default)
[bps]
16 OTHER FUNCTIONS
16-12
170

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info