683161
169
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
TX Inhibit
This function prevents erroneous transmission. When TX Inhibit is
ON, this transceiver does not carry out transmission even when
[PTT] on the microphone is pressed.
The RX audio also becomes inaudible while [PTT] is pressed.
Inhibit transmission in the following cases.
When you want to operate the master transceiver unit as a
receive-only unit during operation in the Split Transfer B mode.
Transmission is not carried out even when this is attempted
using the master transceiver. Audio is also not output.
When you do not wish to transmit signals to the host transceiver
while controlling the transceiver via PC using KNS (KENWOOD
NETWORK COMMAND SYSTEM).
Configure in Menu [6-03] TX Inhibit
Setting Value Off (default)/ On
When TX Inhibit is ON, RX audio is muted when the SS
terminal signal level of the ACC 2 connector is low. RX
audio is also muted while [PTT] is pressed as the signal
level of the SS terminal becomes low.
When TX Inhibit is ON, tuning cannot be performed by
the antenna tuner.
When using this transceiver as a receive-only unit at all
times, configure this setting to “On” to prevent erroneous
transmission.
Packet Cluster Tuning
Packet cluster tuning can be performed by connecting TM-
D710(A/E), TM-D710G(A/E), RC-D710, TM-D700(A/E) or TH-
D72(A/E) to this transceiver.
Connection
.
78
TH-D72(A/E)
Φ2.5mm-Three-pronged Plug
COM Terminal
GND
TXD
RXD
(Female)
9-pin D-SUB Connector
(Solder Side)
9-pin D-SUB
Female
TM-D700(A/E)
PG-5G
RC-D710 + PG-5J
TS-890S
RC-D710 + TM-V71(A/E)
TM-D710(A/E), TM-D710G(A/E)
9-pin D-SUB Male
9-pin D-SUB Female
Receiving Packet Cluster Data
Follow the steps below to operate TM-D710(A/E)/RC-D710/TM-
D700(A/E)/TH-D72(A/E).
1 Switch to the APRS or Navitra mode to receive the
DX packet cluster data.
2 Display the DX packet cluster and align the cursor
with the frequency to tune to.
3 Press the corresponding key to output the
frequency value selected in step 2.
The operating frequency (VFO) is configured based on the
packet cluster data received if the frequency is configurable by
this transceiver.
TM-D710(A/E), TM-D710G(A/E), RC-D710: [TUNE] key
TM-D700(A/E): [MHz] key
TH-D72(A/E): [MENU] key
In the VFO mode, the operating frequency (VFO) that is
currently in use is configured. In the memory channel
mode, the most recent operating frequency (VFO) is
configured.
Only the RX data sent from TM-D710(A/E)/TM-
D710G(A/E)/RC-D710/TM-D700(A/E)/TH-D72(A/E) is
supported.
DX packet cluster data cannot be sent out automatically
to this transceiver.
For TM-D700(A/E), version G 2.0 or later is required to
use this function.
Production of the TM-D710(A/E), RC-D710 and TM-
D700(A/E) have been discontinued.
For more details on the operation information of the DX
packet cluster, please search for information available
on other sources.
OTHER FUNCTIONS 16
16-11
169

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info