683161
94
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Notch Filter
Notch filter is capable of suppressing beat interference at the IF level.
It can be employed to eliminate beat noise and bring up weak
signals or during operation while checking the noise condition.
The notch filter can be used in the SSB, CW, FSK, PSK and AM modes.
Turning ON/OFF Notch Filter
1 Press [NCH].
Pressing [NCH] each time toggles the notch filter between ON
and OFF.
When the notch filter is ON, “NOTCH” is displayed on the
screen.
When notch filter is ON, an indicator showing the notch point
is displayed in the RX filter passband characteristics inside
the filter scope.
.
2 Turn the [NOTCH] control.
Adjust the notch frequency to the point where beat or
interference is to be suppressed.
The notch point indicator moves as the notch frequency
changes.
Once the notch point has been set in the CW mode,
altering the PITCH and SHIFT values will not change the
notch point set for beat suppression.
Switching the Notch Filter Bandwidth
The bandwidth of the stopband for the notch filter can be
configured to normal, middle or wide. The middle and wide
stopbands are wider than the bandwidth of the normal stopband
by two and three times respectively.
Press and hold [NCH].
Pressing and holding [NCH] each time switches the bandwidth
and changes the display as follows.
<< >> (Normal) → << >> (Middle) →
<<
>> (Wide)
Noise Reduction
This transceiver comes with two types of noise reduction functions
NR1 and NR2 which are effective for reducing continuous noise.
When NR1 is used, the optimal method is activated according to
the mode in use.
Noise Reduction 1 (NR1)
In the SSB, FM and AM modes, noise reduction uses a
spectrum subtraction system that places focus on the clarity.
In the CW, FSK and PSK modes, noise reduction employs an
LMS filter system that emphasizes the periodic signal.
The noise reduction effect for NR1 can be adjusted.
Noise Reduction 2 (NR2)
NR2 employs an SPAC system for all modes which extracts the
periodic signal. This system detects periodic signals that are
contained in the RX signals, connects the detected periodic
signals and plays them as part of the RX audio. For this reason,
this method is effective for signals with a single frequency such
as CW signals.
NR2 allows configuration to the optimal RX conditions by
varying the autocorrelation time for periodic signal detection.
NR2 is most effective in the CW mode. (Use of NR1 is
recommended for modes other than CW.)
Beat signals are also suppressed when NR1 is used in
the SSB, FM and AM modes as it suppresses stationary
signals. This is a theoretical behavior and not a
malfunction.
When NR2 is set to ON in the SSB mode, the signal
clarity may deteriorate, or pulse noise or distortion may
occur. This is a theoretical behavior and not a
malfunction.
NR2 cannot be used in the FM mode.
Turning ON/OFF Noise Reduction
1 Press [NR].
Pressing [NR] each time toggles the option in the following
sequence: “NR1” → “NR2” → “OFF”.
When NR1 or NR2 is ON, << >> or << >> is
displayed on the screen.
.
NR1 and NR2 cannot be turned on at the same time.
6 REJECTING INTERFERENCE
6-8
94

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info