683161
17
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Configuration for Switching the RX Bandwidth
Configure the setting as follows to switch the RX bandwidth by cutting off the high or low frequencies within the frequency range of 0 Hz
to 5000 Hz even in the SSB-DATA mode, in the same way as in SSB mode, during operations such as FT8.
* Refer to “Configuring the Behavior of the HI/SHIFT and LO/WIDTH Controls (SSB/SSB-DATA Only)” (6-3).
Configure in Menu [6-12] Filter Control in SSB-DATA Mode (High/Low and Shift/Width). Select “High & Low Cut”.
USB cable and RS-232C straight cable are not supplied with this transceiver. Please purchase commercially available cables.
Delays may occur when using USB audio, and there may also be audio interruptions depending on the performance and load
of the PC.
Place this transceiver far enough from the PC so that noise will not be picked up.
For data communication software settings, refer to the instruction manual or Help file of the software in use.
Virtual COM Port
PC command control using the virtual COM port and USB keying control using the RTS/DTR signal of the virtual COM port can be
performed by connecting this transceiver and the PC using a USB cable.
To use the virtual COM port, Windows 10, Windows 8.1 or Windows 7 is required. (as of January, 2019)
Install the virtual COM port driver on the PC before connecting the USB cable. Download the driver from the following URL.
http://www.kenwood.com/i/products/info/amateur/software_download.html
There are 2 types of virtual COM port on this transceiver, namely virtual COM (Standard) port and virtual COM (Enhanced) port.
The COM port numbers of the virtual COM (Standard) port and virtual COM (Enhanced) port on the PC can be checked using the
following way.
Open the Device Manager in Windows.
Connect this transceiver and the PC using a USB cable. The following 2 COM ports are displayed in “Ports (COM & LPT)” in the
Device Manager.
Silicon Labs CP210x USB to UART Bridge (COM x)
Silicon Labs CP210x USB to UART Bridge (COM y)
x and y are numbers. The numbers vary depending on the PC environment used. The following is the display example of the virtual
COM ports on this transceiver assigned to COM3 and COM4.
.
Double-click on these in the Device Manager to display the respective Properties windows.
Select the “Details” tab and then select “Location paths” from the Property drop-down menu.
Move the mouse cursor to the top line displayed in the “Value” column and check the number in the parenthesis on the right end
of the character string.
The port displayed with the number (1) is the virtual COM (Standard) port of this transceiver.
The port displayed with the number (2) is the virtual COM (Enhanced) port of this transceiver.
The following is the display example of the Properties window of each COM port when the virtual COM (Standard) port and the virtual
COM (Enhanced) port are assigned to COM3 and COM4 respectively.
.
INSTALLATION AND CONNECTION 1
1-5
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info