683161
16
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
PC Connection for Data Communication
This transceiver is equipped with data communication connectors (USB and ACC2) for exchanging audio signals with the auxiliary
equipment and connectors (USB and COM) for controlling using PC commands when performing data communication with an external
device such as a PC as the auxiliary equipment.
To make use of data communication such as RTTY (AFSK), PSK31, SSTV, JT65 and FT8 using data communication software that
employs the sound function of a PC and with this transceiver configured to the DATA mode (SSB-DATA, FM-DATA, AM-DATA), set up
the connection as follows.
When using the USB audio function: connect to the PC using a USB cable. Data communication with only the USB cable connection
is possible by making use of data VOX or PC commands (TX1; to start transmission and RX; to end transmission) to switch between
transmission and reception. (For details on the configuration of the input sound source in the DATA mode and the VOX function, refer
to page 8-1.)
When using an ACC 2 connector: connect the audio output line of the PC to pin 11 (ANI) of the ACC 2 connector and the audio input
line of the PC to pin 3 (ANO). Pin 9 (PKS) of the ACC 2 connector, data VOX or PC commands (TX1; to start transmission and RX;
to end transmission) are used to switch between transmission and reception.
When controlling using PC command, connect to the PC with a RS-232C straight cable or a USB cable. To connect with a USB cable,
use the virtual COM (Standard) port. For more details, please refer to “Virtual COM Port” (1-5).
For performing RTTY keying by connecting to a PC (or other external devices) while this transceiver is configured to the FSK mode,
please refer to “Operating RTTY (FSK) Using an External Device” (5-22).
.
USB (B) Connector
USB Cable
Supplied 13-Pin DIN Plug
(Use the supplied 13-pin DIN
plug to make your own
connection cable.)
To USB Port
PC
To Audio Input/Output Port
To RS-232C
Serial Port
(Female)
TS-890S
RS-232C Straight Cable
Configure the transceiver as follows according to the method of connection with the PC, the specification of the software used for data
communication and the settings, etc.
Baud Rate Configuration for PC Control
Configure the baud rate of the COM/USB port used for PC control as follows.
* Refer to “Configuring the COM/USB (Rear Panel) Baud Rate” (16-5).
When using the USB port: Configure in Menu [7-01] Baud Rate (Virtual Standard COM).
When using the COM port: Configure in Menu [7-00] Baud Rate (COM Port).
Audio Source Input Configuration
Configure the audio source input for data transmission via PC commands in the SSB-DATA mode as follows.
* Refer to “Configuration of the Input Path of TX Audio” (8-1).
1) Press and hold [DATA] to display the audio source input screen.
2) Press [DATA] to switch from “Data Mode Off” to “Data Mode On”.
Check the “Rear” setting under “Audio Input” for “DATA SEND (PF)” under “TX Method”.
When using the USB audio function: Configure to “USB Audio” (default).
When using the ACC 2 connector: Configure to “ACC 2”.
RX Level Adjustment
Adjust the audio output level for receiving via data communication as necessary by using the sound setting (recording device) on the
PC or using the following menus on the transceiver.
* Refer to “Configuring Audio Input/Output” (16-7).
When using the USB audio function: Configure in Menu [7-08] USB: Audio Output Level.
When using the ACC 2 connector: Configure in Menu [7-09] ACC 2: Audio Output Level.
TX Level Adjustment
Adjust the audio input level for transmitting via data communication as necessary by using the sound setting (playback device) on the
PC or using the following menus on the transceiver.
* Refer to “Configuring Audio Input/Output” (16-7).
When using the USB audio function: Configure in Menu [7-06] USB: Audio Input Level.
When using the ACC 2 connector: Configure in Menu [7-07] ACC 2: Audio Input Level.
1 INSTALLATION AND CONNECTION
1-4
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info