686377
13
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
13
A3 MIG Welder© Kemppi Oy 2018 1826
INTEGRATION GUIDE
5.1.3 FineTuning
This 16-bit function controls the ne tuning of the synergic
voltage for all processes except the MIG process. For the
MIG process the Voltage value is used instead. The value
is given in scaled or non-scaled mode, depending on
the user setup. The ne tuning is scaled using the robot
scaling value. The range of the ne-tuning value depends
on the selected process.
In non-scaled mode, 1-MIG process:
The minimum setup value is 0 (-9.0).
The maximum setup value is 180 (9.0).
The minimum technical step is 1 (0.1).
The minimum signicant step is 5 (0.5).
In non-scaled mode, WiseRoot and WiseThin processes:
The minimum setup value is 0 (-5.0).
The maximum setup value is 100 (5.0).
The minimum technical step is 1 (0.1).
The minimum signicant step is 5 (0.5).
In scaled mode, 1-MIG process:
The minimum setup value is 0 (-9.0).
The maximum setup value is the robot scaling
value, which is interpreted as 9.0.
The minimum step is 1. The ne tuning is
calculated from the setup value by means of the
value scaling formula.
In scaled mode, WiseRoot and WiseThin processes:
The minimum setup value is 0 (-5.0).
The maximum setup value is the robot scaling
value, which is interpreted as 5.0.
The minimum step is 1. The ne tuning is
calculated from the setup value by means of the
value scaling formula
The value has an eect only when the OnlineControl
signal is set (1), and it overrides the corresponding memory
channel value. If the OnlineControl signal is cleared (0), the
ne tuning from the active memory channel is used.
5.1.4 MemoryChannel
This 8-bit function controls the active memory channel.
The system automatically brings all parameters from the
memory channel into use, including those for the welding
process, welding parameters, and welding functions.
There are up to 90 memory channels available in the
system. They are numbered 0 to 89. The memory channel
can be changed during welding.
The minimum setup value is 0.
The maximum setup value is 89. All values above
that are automatically interpreted as 89.
The minimum step is 1.
5.1.5 SimulationMode
This signal function turns the simulation mode on and o.
In the simulation mode ArcOn, CycleOn, and the other
necessary signals are simulated locally to enable the
welding robot to act as in a normal welding operation.
Welding power remains o and wire is not fed during
simulation. The simulation mode is not allowed during
welding, so changing this signal during welding (or
simulation) has no eect.
0 = Simulation mode o. The StartWelding
function controls a normal welding sequence.
1 = Simulation mode on. The StartWelding
function controls a simulation sequence.
5.1.6 StartWelding
This signal function controls the welding sequence. If the
SimulationMode is set to be on, it controls a simulation
sequence instead.
0 = Welding / simulation o
1 = Welding / simulation on
5.1.7 WireInch
This signal function feeds the welding wire forwards. The
wire is fed at the speed of 1.0 m/min for 3 seconds and
then stepped to 5.0 m/min.
0 = Wire inch o
1 = Wire inch on
This signal has no eect during welding or simulated
welding.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A3 MIG Welder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A3 MIG Welder in de taal/talen: Engels als bijlage per email.

De handleiding is 2,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info