502558
33
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
SYSTEM CONFIGURATION 33
ENGLISH
System Configuration
that will have on the speaker’s performance. If
you do not have access to the owner’s manual
for a particular speaker, you should be able to
obtain the needed information from the Web site
or customer service department of the speaker’s
manufacturer.
To manually adjust the speaker settings, go to
the
SPEAKER SIZE menu by pressing the
OSD Button
L
on the remote and when the
MASTER MENU (Figure 7) appears, press the
/
¤
Navigation Button
E
until the cursor
is on the
MANUAL SETUP line and press the
Set Button
F
. When the MANUAL
SETUP
menu (Figure 18) appears, press the
/
¤
Navigation Button
E
again until the
cursor is on the
SPEAKER SIZE line and
press the Set Button
F
.
On the
SPEAKER SIZE menu (Figure 19)
you will see a display of either the settings that
were established when EzSet/EQ was run, or the
factory default settings if you have not yet run
the automated system.
Figure 19
To change the setting for any of the four speaker
positions, press the
/
¤
Navigation Button
E
until the cursor points to the line where you
wish to make the change. Press the
/
Navigation Button
E
to change the setting,
but note that when you do this for the first time
in the menu, a warning message (Figure 20) will
appear in the on-screen display reminding you to
rerun EzSet/EQ after you are finished with any
speaker configuration changes. This is necessary
to make any level output adjustments needed
after the setting changes so that the new
configuration will be properly integrated.
Figure 20
The warning message will remain for four
seconds and then the
SPEAKER SIZE
menu will return to the screen. At this point you
may change the settings to the “size” or
crossover for any of the four speaker positions
using the Navigation Buttons
E
as shown
above. The information below details the settings
available for each of the speaker configurations.
At each of the four speaker position lines, you
have the option to set the speaker size and
crossover. Note that the “size” does not refer to
the speaker’s actual physical size, but rather to
the ability of the speaker to reproduce low-fre-
quency information. If your speakers at any
position are traditional full-range models capable
of handling the full audio spectrum, select
LARGE. These speakers are called “large”
since the low-frequency drivers required to play
bass without strain or distortion are typically
eight to fifteen inches in diameter, in turn making
the speaker cabinet larger than those with small
(or no) low-frequency drivers. When the speakers
at a particular position are smaller frequency-
limited speakers that do not have the ability to
properly reproduce low-frequency sounds, select
SMALL.
At all speaker positions except for the front
left/right speakers, you may also select
NONE.
This setting tells the system that no speakers are
present at that position, allowing the AVR to
select the correct surround modes that are com-
patible with the number of speakers installed. For
example, in order to use the Dolby Digital EX,
Dolby Pro Logic IIx, DTS-ES, Logic 7/7- channel
and “7 Stereo” modes, you must have either
LARGE or SMALL speakers entered as the
setting for the
BACK SURR channels.
When
LARGE is selected for any channel, a
full-range signal will be sent to the speaker out-
puts for that channel. For all speaker positions
except the front left/right, when
LARGE is
chosen, no derived sound will be sent to the sub-
woofer output, although in all cases the special
low-frequency effects (LFE) signals available on
5.1 or 6.1 digital programs will always be sent to
the subwoofer output.
When
SMALL is selected for any channel, you
may also enter a setting for the crossover fre-
quency at which sound is divided between the
frequency above which sound is sent to the
channel’s speakers and below which sound is
sent to the subwoofer. When configuring a
“small” speaker, choose the setting that has the
frequency closest to that of the lowest frequency
the speakers in question are capable of handling.
If one of the six available crossover points does
not match, select the one that is above, but
closest to, the speaker’s low-frequency limit.
When there are no speakers available at a
specific position, select
NONE. When this option
is chosen for the Center or Side Surround
speakers, the sound that would normally be sent
to these channels will be split between the front
left and right speakers. Note that when your
system does not include Center or Surround
speakers, the use of Dolby Virtual Speaker as a
surround mode may provide a sound field that
simulates the presence of these speakers. (See
page 39 for more information on the Dolby
Virtual Speaker mode.)
Note that when
NONE is selected for the Back
Surround speakers, the 6.1/7.1 channel surround
modes are not available. When this is the case
for your system you may wish to take advantage
of the availability of the unused amplifier channel
pair to power a second set of speakers in another
room. See page 33 for more information on
amplifier configuration.)
Once any desired changes have been made to
the speaker size and/or crossover, press the
/
¤
Navigation Button
E
to move the
cursor to any other line on this menu to make a
setting change, or go to the
BACK TO
MANUAL SETUP
menu and then press the
Set Button
F
to continue with overall
configuration.
LFE Low-Pass-Filter Setting
The LFE LP FLT line selects the frequency
setting below which sounds that may be avail-
able from a special low-frequency effects (LFE)
track are sent to the subwoofer. In most cases,
this setting will be set accurately by EzSet/EQ
but, should you wish to make a change from that
setting or the 120Hz frequency that is most
commonly used in the creation of LFE channels
by motion picture sound mixers, after making
sure that the
SPEAKER SIZE menu (Figure
19) is on the screen, press the
/
¤
Navigation Button
E
so that the cursor is
pointing to
LFE LP FLT. Press the
/
Navigation Button
E
to begin the selection
process, and note that the warning message
(Figure 20) will appear reminding you to rerun
EzSet/EQ after all changes have been made.
When the
SPEAKER SIZE menu returns to
the screen, press the
/
Navigation Button
E
to make your selection. When the desired
setting appears, press the
/
¤
Navigation
Button
E
to move the cursor to any other line
on this menu where you wish to make a setting
change, or go to the
BACK TO MANUAL
SETUP
menu and then press the Set Button
F
to continue with overall configuration.
* X-OVER CHANGE WARNING *
Speaker X-Over Freq or
Size has been changed.
Please re-run EZSET/EQ
* SPEAKER SIZE *
FRONT L/R :SM - 100Hz
CENTER :SM - 100Hz
SIDE SURR :SM - 100Hz
BACK SURR :SM - 100Hz MAIN
LFE LP FLT :120 Hz
SUB MODE :SUB
SUB SIZE :10in/250mm
EZSET SETTINGS: OFF ON
BACK TO MANUAL SETUP
29851_AVR645_ENG 30/10/06 9:46 Side 33
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR645 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR645 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon AVR645

Harman Kardon AVR645 Gebruiksaanwijzing - Nederlands - 68 pagina's

Harman Kardon AVR645 Gebruiksaanwijzing - Deutsch - 68 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info