502558
27
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
SYSTEM CONFIGURATION 27
ENGLISH
System Configuration
Surround Setup
The next step for that input is to set the surround
mode you wish to use with that input. Since sur-
round modes are a matter of personal taste, feel
free to select any mode you wish – you may
change it later. The Surround Mode chart on page
38 may help you select the mode best suited to
the input source selected. For example you may
select Dolby Pro Logic II or Logic 7 for most
analog inputs and Dolby Digital for inputs con-
nected to digital sources. In the case of inputs
such as a CD Player, Tape Deck or Tuner, you may
wish to set the mode to Stereo, if that is your
preferred listening mode for standard stereo
sources, where it is unlikely that sur
round encod-
ed material will be used. Alternatively, the 5
Channel Stereo or
Logic 7 Music mode may also
be a good choice for stereo-only source material.
It is easiest to complete the surround setup using
the full-OSD on-screen menus. From the
MASTER menu (Figure 7), press the
/
¤
buttons
E
F until the cursor is next to the
SURROUND SELECT menu. Press the Set
Button
F
Q so that the SURROUND
SELECT
menu (Figure 13) is on the screen.
Figure 13
The first line on the menu allows you to select
the input for which the specific surround settings
will be applied. Press the
/
Navigation
Buttons
E
F to select the input source to
be configured.
The
AUDIO IN-PORT and AUDIO IN
lines are for display only and may not be
changed through the
SURROUND SETUP
menu. The AUDIO IN-PORT displays the
physical connection source for the current active
input, and the
AUDIO IN line shows the
signal type present. Note that an
UNLOCK
message in the AUDIO IN line indicates that
a digital physical input source has been selected,
but that no data stream is present.
When the input selection has been made, press
the
/
¤
Navigation Button
E
F to move
to the next configuration line.
The ADC SAMPLINGline is where you
determine whether the unit’s upsampling feature
is turned on or off.The default setting of 48kHz
puts the feature in a bypass, or “off, mode and
will pass digital audio data through the DSP at
its native sample rate. To process incoming
44.1kHz signals at a higher resolution,
upsampled 96kHz sample rate, press the
/
Navigation Buttons
E
F once so that
96kHz is highlighted.
When the desired setting has been made, or if no
adjustment is required at this line, press the
/
¤
Navigation Button
E
F to move to
the next configuration line.
The
SURR MODE and SELECT lines are
related, as they guide you to the choice of the
surround mode that will be activated whenever
the input being configured is selected.
At the
SURR MODE line, press the
/
Navigation Buttons
E
F to select the sur-
round mode group (such as Dolby modes, DTS
modes, Logic 7 modes, and DSP or Stereo modes)
that is applicable to the input source. After mak-
ing a selection, press the
/
¤
Navigation
Button
E
F to move to the SELECT line.
At the
SELECT line, you are able to choose
the specific mode to be used from within the
major surround mode group. The choice of modes
is governed by the input type (as some modes
such as Dolby Digital or DTS-ES are not available
for analog sources), as well as by the speaker
configuration, since some modes are only
available when a full 7.1 speaker complement is
present. The full list of available modes is
detailed in the surround mode chart on page 38.
In addition, you may also use the settings in the
SURROUND CONFIG menus to delete
modes you do not normally use from the
available choices.
When both a surround mode group and a
specific surround mode have been selected, press
the
/
¤
Navigation Button
E
F to move
to the next configuration line.
The
DEFAULT SURR mode line is where you
choose the mode that is activated when a digital
source is selected. The factory default setting of
LAST will activate the last-used mode for any
digital source. If you prefer to always have a digi-
tal source switch to the specific mode encoded
by digital data flags in the incoming audio data
stream, press the
/
Navigation Buttons
E
F so that ORIGINAL appears.
Before proceeding to the
SURROUND
CONFIG
line, it is worth noting that the set-
tings in the submenus attached to that line may
require a considerable amount of time to com-
plete. Although they are useful in that they allow
you to customize the list of surround modes that
appear in normal use of the AVR, you may wish
to bypass those settings at this time so that you
may complete the configuration process. You may
return to this menu line at a later time, once you
have had a chance to listen to the various sur-
round modes and determine which you want to
“keep” and which you do not want to use. The
settings in this line are not primary controls and
do not impact the way the AVR “sounds.
To proceed to the
SURROUND CONFIG
line, press the
/
¤
Navigation Button
E
F to move to that line; otherwise, press it
again to move to the
DOLBY SURR
SETUP
line and skip to the instructions for
that setting.
The
SURROUND CONFIG line is your
gateway to a broad range of surround mode
configurations. To continue, press the Set
Button
F
Q to go to the main
SURROUND CONFIG menu (Figure 14).
Figure 14
The LOGIC 7 GLOBAL line is the only item
on this menu page that is menu-specific, and it
allows you to select whether or not Logic 7 will
be the default surround mode for any incoming
audio signal. The default setting is
OFF, which
chooses the native mode. Press the
/
Navigation Buttons
E
F so that ON
appears, to activate the global Logic 7 setting for
this input.
The remaining five items in this menu are global
settings that take you to a submenu listing the
individual surround modes available within the
selected mode group. To select a surround mode
list, press the
/
¤
Navigation Button
E
F until the on-screen cursor is pointing to
the desired mode, and then press the Set
Button
F
Q. Within each menu, press the
/
¤
Navigation Button
E
F to move the
cursor up and down through the list, and then
press the
/
Navigation Buttons
E
F to
turn the mode “ON” or “OFF.
** SURROUND CONFIG **
LOGIC 7 GLOBAL:OFF
DOLBY MULTI CONFIG
DOLBY 2.0 CONFIG
DTS CONFIG
PCM 44.1/48kHz CONFIG
PCM 96k CONFIG
BACK TO SURROUND CONFIG
** SURROUND SETUP **
SOURCE: VIDEO 1
AUDIO IN PORT: ANALOG
AUDIO IN: PCM 44.1kHz
ADC SAMPLING: 48K 96K
SURR MODE: LOGIC 7
SURR SELECT: MUSIC 5.1
DEFAULT SURR: LAST
SURROUND CONFIG
DOLBY SURR SETUP
BACK TO MASTER MENU
29851_AVR645_ENG 30/10/06 9:46 Side 27
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR645 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR645 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon AVR645

Harman Kardon AVR645 Gebruiksaanwijzing - Nederlands - 68 pagina's

Harman Kardon AVR645 Gebruiksaanwijzing - Deutsch - 68 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info