812036
9
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
9
The duration of this procedure is approx. 2
minutes.
The values thereby measured are the basis
for whether or not the device can continue its
operation and which LED’s light up for the
„optical visualization of the burner soiling“.
5.5. Cooling
If the set target room temperature is reached,
i.e. actual room temperature and target room
temperature match, then the controller
switches over to the operating state „Cooling“.
The conveying of the fuel is terminated, i.e.
the screw conveyor which is located in the
worm tube stops, the speed of the induced
draught blower is regulated to a precisely
defined speed and the fuel, which is still in the
burner tray, is burned.
The convection air blower is regulated to a
precisely defined speed.
The cooling phase is limited time-controlled.
(duration approx. 15 minutes)
After completion of the operating state
„Cooling“, the device switches to the
operating state „Standby“.
5.6. Standby
In this operating state, no combustion
operation takes place, all components,
induced draught blower, convection air blower
and screw conveyor are stationary, the
ignition is switched off, the device is in
„Standby position“.
Before the stove can switch from the
operating state „Standby“ to the operating
state „Start phase“ again, two starting
conditions must be fulfilled:
1. The set target room temperature must
be undershot by at least 1.0 °C
2. The waste gas temperature measured
with the waste-gas temperature sensor
must be less than 70 °C
Only when both starting conditions are
fulfilled does the device switch from the
operating state „Standby“ back to the
operating state „Start phase“.
Attention!
In „Standby-mode“ the device starts
automatically. Due to the development of
heat on the panel, it must be ensured, that
no unsupervised persons who are not
familiar with the operation of the pellet
stove remain in the room of installation.
The placing of non-heat-resistant
materials and objects on the stove and
within the prescribed minimum distances
is forbidden.
5.7. Safety shutdown
If a fault occurs, regardless in which operating
state and during which mode, then a safety
shutdown is initiated.
The sequence of the safety shutdown is
precisely defined.
During the safety shutdown, the components
are switched as follows:
Induced draught blower – ON
Convection air blower - ON
Screw conveyor – OFF
Ignition – OFF
The end of the safety shutdown is
temperature-dependent, i.e. the operating
state „Safety shutdown“ is retained so long
until the stove has cooled to a waste-gas
temperature of less than 80 °C.
After conclusion of the safety shutdown, the
controller switches over to the operating state
„Fault“.
5.8. Fault
The stove can no longer be operated
automatically.
The operator can read off the fault on the
display.
After proper remedy of the fault and
acknowledgement of the error message on
the control unit, the stove can be set into
operation again.
5.9. Shutdown – Operating State OFF
Method of procedure:
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Haas-Sohn COMPACT-PELLET 310 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Haas-Sohn COMPACT-PELLET 310 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Haas-Sohn COMPACT-PELLET 310

Haas-Sohn COMPACT-PELLET 310 Gebruiksaanwijzing - Deutsch - 43 pagina's

Haas-Sohn COMPACT-PELLET 310 Gebruiksaanwijzing - Français - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info