769010

Giordani Citywave Handleiding

22
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
42
UK
GIORDANI CITYWAVE MODULAR SYSTEM (FROM 0 TO 36 MONTHS APPROXIMATELY)
STROLLER
OPENING THE STROLLER
1. As shown in Fig. 1a, pull the folding handle
on both sides, following the direction of the
arrow. At the same time, pull the stroller han-
dle to expand the stroller frame. As shown
in Fig. 1b, push the pedal down completely
in order to lock the frame in position. Check
that the two tubes are fully connected as
shown in Fig. 1c to ensure that it is fully open.
WARNING: When the child is seated, never
pull the closure handle on both sides if the
frame is not locked into position.
ASSEMBLY OF WHEELS
2. As shown in Fig. 2a/2b, insert the front and rear
wheels in the specic housings and these will
be tted correctly only when you hear a “CLICK”.
WARNING: Before use, try moving and rotat-
ing the wheels manually to make sure that
they are all properly tted in their housings.
ASSEMBLY OF HOOD
3. As shown in Fig. 3a, open the seat in the direc-
tion of the arrow. As shown in Fig. 3b, insert the
hood frame in the specic housing on the seat.
It is fully fitted when you hear a “CLICK”. As
shown in Fig. 3c/3d, fasten the snap buttons
and fasten the seat and hood Velcro strap to
complete the assembly as shown in Fig. 3e.
ASSEMBLY AND REMOVAL OF SEAT
4. Assembly: As shown in Fig. 4a, open the seat
completely and insert both side ends in the
specic frame housings (align the arrow indi-
cating the insertion point with the frame rivet).
It is fully tted when you hear a “CLICK”. Be-
fore use, make sure the set is tted properly.
Removal: As shown in Fig. 4b, to release the
lock press the buttons under each armrest and
pull the seat out of the frame at the same time.
WARNING: before use, check that the seat is
correctly secured.
FITTING AND REMOVING THE FRONT SECURITY BAR
5. Assembly: As shown in Fig. 5a, insert the ends
of the safety bar into the appropriate slots on
both sides of the seat at the same time.
Removal: As shown in Fig. 5b, press the front
bar release buttons at the same time, then
remove it.
OPENING THE HOOD
6. As shown in Fig 6a, push outwards to fully open
the hood. The stroller will have been complete-
ly assembled when it looks like in Fig 6b.
WARNING: Failure to read these instructions
could compromise the child's safety, read
them carefully.
TURNED SEAT
7. As shown in Fig 7a, push down the same but-
ton that you would operate to detach the seat,
then remove it and turn it.
BACKREST ADJUSTMENT
8. As shown in Fig 8a, push the backrest adjust-
ment button to raise or lower it. (3 positions).
ADJUSTMENT OF THE LEG REST
9. As shown in Fig 9a/9b, push the leg support
adjustment buttons located underneath it to
raise or lower it, then proceed adjusting it.
WHEEL OPERATION
10. Use of the swivel wheels: as shown in Fig
10a, turn the wheel lock devices (to the left
and right of the wheels) outwards, thus al-
lowing the wheels turn. As shown in Fig 10b,
turn the wheel lock devices (to the left and
right of them) inwards and the wheels will
lock in a straight position. Quick removal of
the wheels: as shown in Fig. 10c, press the
release button and at the same time pull the
FRONT wheel, applying a minimum force.
As shown in Fig. 10d, press the release but-
ton and at the same time push the REAR
wheel out, applying a minimum force. Use
the locking device: as shown in Fig 10e, to
lock the rear wheels, press the locking de-
vice down with the foot. When the indicator
(d) turns RED, this means that the brake
is enabled. To unlock the wheels, push the
locking device down with your foot. When
the indicator (d) turns GREEN, this means
that the wheel brake has been disabled.
43
WARNING: Push the stroller back and forth
to make sure the brake has been correctly
enabled.
USING THE RETENTION BELTS
11. Fastening: first, insert the buckles connect-
ed to the retention straps of the child's
waist (C & D) in the corresponding hous-
ings connected to the shoulder straps, as
shown in Fig 11a. Then insert the E & F
parts in the central button G, as shown in
figure 11b. When a CLICK is heard, it will
be completely inserted. Unfastening: press
the central button (G) to remove (E & F).
Adjusting the safety strap: as shown in Fig
11c, tighten or loosen the belt for the child's
comfort. Adjust the height of the shoulder
retention belt: the position (H) is suitable
for children aged over 6 months. Position (I)
is suitable for children under 6 months. To
change the height, insert the shoulder re-
tention strap inside the belt cover and insert
the end inside the backrest. Next, secure
the shoulder strap to the desired height.
WARNING: Always check that the child re-
straint system is always tightly closed and
adjusted when using the stroller.
ACCESSORIES
ASSEMBLY AND REMOVAL OF THE ADAPTER
12. Assembly: As shown in Fig. 12a, insert the
two adapters inside the housings in the frame
structure. The assembly is considered correct-
ly carried out when it appears as in Fig. 12b.
Disassembly: As shown in Fig. 12c, press the
release buttons on the adapter and remove it.
ASSEMBLY AND REMOVAL OF THE CAR SEAT
13. Assembly: As shown in Fig. 13a, insert the
ends of the car seat into the housings in the
adapters mounted on the frame structure.
When you hear a CLICK, they will have been
completely inserted.
Disassembly: Depending on the type of re-
lease button available on the modular system,
choose the most suitable method. Method A:
as shown in Figure A, pull upwards the release
button "a" on the back of the car seat, then lift
the seat as shown in Fig. 13b.
Method B: as shown in Figure B, press the side
button "b" downwards and at the same time
push the button "c" upwards, then raise the
seat as shown in Fig. 13b.
ASSEMBLY AND DISASSEMBLY
OF THE CARRYCOT
14. Assembly: As shown in Fig. 14a, insert the
ends of the carrycot inside the housings lo-
cated in the adapter mounted on the modular
system structure. When you hear a CLICK,
they will have been completely inserted.
Disassembly: As shown in Fig. 14b, press the
release button located under the carrycot
and unhook it.
WARNING: choose the appropriate instructions
according to the carrycot purchased. Remove
the seat before installing the car seat.
HOW TO CLOSE THE MODULAR SYSTEM
15. As shown in Fig. 15a, fold the hood following
the direction indicated by the arrow. As
shown in Fig 15b/15c, press the backrest
adjustment button downwards and lower it
as far as possible. As shown in Fig. 15d, pull
the closing hook from both sides following
the direction indicated by the arrow. Then
push the handle downwards to unlock the
modular system frame. As shown in figure
15e, push the same pedal upwards with the
foot, which is used to fold the structure, so
that the structure will be released, then raise
the closure handle as shown in Fig. 15f. When
a CLICK is heard, the modular system will be
completely closed as shown in Fig. 15g.
CLEANING AND CARE
Clean and maintain the modular system regularly
to eliminate any danger of accidental injury to the
child. Clean the seat with a brush and the remain-
ing parts with soap or neutral detergent. Regularly
inspect the modular system to identify defects
such as loose screws, damaged parts or broken
seams. Provide for xing the defects if necessary.
To avoid damage to the modular system, read the
instructions carefully before installing it.
… 22 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Giordani Citywave bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Giordani Citywave in de taal/talen: Nederlands, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 5,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info