724644
15
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 61705 • 08/2018 • FCS4800A
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
47.1cc Petrol Chainsaw
MODEL: №. 61705 • 08/2018 • FCS4800A
26 27
Bucking (Fig AK)
Bucking is cutting a log into lengths for easier
handling.
To saw a log lying on the ground, rst saw
halfway, then roll the log over and cut from the
opposite side. To saw the end of a log supported
o the ground, rst saw up from the bottom
one-third through the log then nish by sawing
down from the top. To saw a log in the middle of
two supports holding it o the ground, rst saw
down from the top one-third through the log
then nish by sawing up from the bottom.
CAUTION: Avoid cutting into the ground as
this will very quickly dull the saw chain.
Pruning (Fig AL)
Pruning is the removal of a limb or branch from a
standing tree.
WARNINGS: Do not use an unstable
foothold or ladder. Do not overreach.
Do not saw above shoulder height. Always use both hands to hold the
chainsaw. First cut up from the bottom and nish down from the top.
1
2
1
2
1
2
1
2
AK.
1
2
1
2
1
2
1
2
AL.
1. Clear the area around the tree and make sure that you have a good foothold
and clear retreat path.
2. Ensure that others in the area are aware of the felling and ensure people and
animals are well clear.
3. Make a notch cut one-third of the way into the tree on the felling side.
4. Make the felling cut on the opposite side to the initial notch and slightly
higher than the notch. As the felling cut gets close to the notch cut, the tree
will begin to fall.
5. Remove the chainsaw from the cut, and stop the engine with the on/o
switch (4), put the chainsaw down and leave the area along the retreat path.
Limbing (Fig AJ)
Limbing is the process of removing the
branches from a fallen tree.
Check the direction in which a branch will
bend before cutting it. Always cut on the op
-
posite side to the bending direction so that
the guide bar (19) is not pinched in the cut.
For large limbs that cannot be removed in
one cut, make an initial cut from the bent
side and nish by sawing from the opposite
direction.
Do not remove limbs that are supporting the fallen tree on the ground until the
tree has been cut into lengths.
WARNINGS: Always keep a balanced stance. Do not stand on the log.
Be alert to the fact that the log may roll over. When working on a slope,
always stand on the uphill side of the log.
1
2
1
2
1
2
1
2
AJ.
Operation Operation
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gardenline FCS4800A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gardenline FCS4800A in de taal/talen: Engels als bijlage per email.

De handleiding is 1,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info