724644
9
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 61705 • 08/2018 • FCS4800A
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
47.1cc Petrol Chainsaw
MODEL: №. 61705 • 08/2018 • FCS4800A
14 15
7. Once the chain (20) is in position around the
nose of the guide bar (19), ensure that the chain
links are located within the bar guide channel,
(Fig G), and the chain (20) is fully located around
the drive sprocket (29).
8. On the chain drive side cover (23), adjust the
chain tensioning screw (37) in an anti clockwise
direction as per the following, so the assembly
of the guide bar (19) is NOT tight on the chain
(20). When replacing the existing chain, rotate
the adjustment screw 5 FULL turns in an anti-
clockwise direction.
When replacing with a new chain, rotate the
adjustment screw 10 FULL turns in an anti-
clockwise direction (Fig H).
9. After adjusting the chain tensioning screw
(37), replace the chain side cover (23) on to the
chainsaw and hold the cover rmly against the
Bar. DO NOT t the nuts (Fig I). While holding
the cover on rmly, grasp the guide bar (19) and
slide it outward slowly (Fig J).
When the chain tensioning pin (30) aligns with
the clearance hole in the bar, the cover will drop
rmly and at on the bar (Fig L - shows internal
side on chain drive side cover and where the
chain tensioning pin is located).
If the chain tensioning pin (30) does not align,
adjust the chain tensioning screw (37) using the
combination tool (at blade screwdriver) (32) so
the pin aligns with the hole in the bar (Fig K).
The chain tensioning pin (30) must enter the guide bar (19), and the at
faces of both the chainsaw and chain drive side cover (23) must be at
against the bar before the nuts are applied.
10. Fit the chain drive side cover nuts (24) and tighten FINGER TIGHT (Fig M).
Check again the cover is at on the surface of the bar.
11. Rotate the chain (20) a few times to ensure the chain (20) is free to rotate
around the drive sprocket (29) and is correctly engaged on the sprocket.
12. Check the tension of the chain (20). It will need to be tightened. Tighten
the chain tensioner screw (37), in a clockwise direction (previous Fig K)
until the links of the chain just touch the bottom edge of the guide
bar (19).
The chain should be fully seated in the bar channel. DO NOT over tighten.
The chain (20) should be able to be lifted at least 5mm in the centre of the
bar (Fig N).
13. Tighten the chain drive side cover nuts (24) rmly using the supplied
combination tool (bar nut tube spanner) (32) (Fig O).
CAUTION: A new chain (20) will stretch after just a few minutes of use.
Check and, if necessary, re-adjust the chain tensioning screw (37).
A loose chain causes rapid wear to both the chain (20) and the guide bar
(19) and could derail causing a major safety hazard.
NOTE: Do not make ANY adjustments with the chainsaw engine running.
14. To tighten a loose chain (20), loosen the chain drive side cover lock nuts
(24), then using the supplied combination tool (at blade screwdriver)
(32), turn the chain tensioning screw (37) clockwise to tighten the chain
(20) (Fig H). Do not over tighten, the chain (20) should be able to lift 5mm
from the middle of the bar.
15. Retighten the chain drive side cover nuts (24) rmly using the supplied
combination tool (at blade screwdriver) (32) (Fig O). Run the chainsaw
for approximately 30 seconds and then turn the chainsaw o. Retest the
chain.
Assembly Assembly
I.
J.
K.L.
O.M.
TIGHTEN
TIGHTEN
N.
5MM
H.
5 FULL
TURNS
ANTICLOCKWISE
G.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gardenline FCS4800A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gardenline FCS4800A in de taal/talen: Engels als bijlage per email.

De handleiding is 1,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info