633026
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
9
7.0 - RAPID TEST
WARNING:
- Ensure that the alarm is disarmed.
A - Earth the GREEN/YELLOW wire until the alarm system emits a long acoustic signal and
the LED BUTTON starts flashing.
B - After about 10 seconds the alarm system will emit 3 visual (indicators)/acoustic signals
and it will enter automatically the RAPID TEST function. The alarm system can be considered
correctly installed if:
1 - The PINK wire has a positive signal (+12V) output and the additional sensors/modules
connected to this wire activate.
2 - When opening one of the doors (GREEN/BROWN or GREEN/BLUE wires) and the bonnet/
boot (GREEN wire) you will obtain a visual (indicators)/acoustic signal.
3 - When you activate an additional sensor (GREEN/BLACK wire) you will obtain 2 flashings
of LED BUTTON and a visual signal (indicators).
4 - When you activate the ultrasonic sensor you will obtain a visual signal (indicators).
To test the alarm, remove all possible items that may create movements and ensure that
doors and windows are closed. Introduce your arm through the gap and move it around; the
alarm system indicators will flash to confirm correct operation. To increase the sensitivity, turn
the adjuster close to the main alarm connector clockwise (see page 4).
Warning: this procedure is one of the most important correct alarm operation. To check tthe
sensitivity, move your arms across the outside of the window and the soft top roof, this should
not trigger the alarm. Only the introduction of an object should trigger the alarm.
5 - If you press the ANTI-HIJACK FUNCTION reservation button (BLACK/WHITE wire) you
obtain a visual (indicators)/acoustic signal.
6 - When the ignition key is ON you will obtain an acoustic signal (if an additional GT 843
siren is connected, this will sound for about 1 second).
6 - Unlock the vehicle using the original remote control, after a couple of seconds the alarm
will emit 2 visual signals (indicators), and 3 acoustic signals indicating the end of self coding
and the doors will unlock.
Warning: The procedure can be considered carried out correctly only if the operations are in
compliance with the points 5 and 6. On the contrary wait that the alarm system comes out
automatically from the procedure (the alarm system will emit an acoustic signal).To repeat
the procedure disconnect the positive leave for a few seconds and then reconnect. Start the
procedure again from point 1.
Note: supposing that the self-coding procedure has been completed correctly, but you want
to repeat it, for example in the case of the alarm command wires connection (i.e. RED/BROWN,
YELLOW/BROWN, RED/GREY AND YELLOW/GREY wires) has to be changed, it is
necessary to repeat the signals self-coding procedure from the point 1, remember to
disconnect the alarm system power supply for some seconds.
If a self-coding procedure hasn’t been correctly carried out the system can only be
disarmed by the “GT CARD CODE” (see the relative section). Once the alarm is
disarmed, proceed with the self-coding before using the original vehicle’s remote control
handset.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw GT 800-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van GT 800-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info