679143
17
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
FBK 4 C2
12 
GB│IE│NI
Installing/replacing the strimmer
Install/replace the strimmer as displayed in figure 2c.
Find the hole in the drive plate

, align it with the opposite hole and
block it with the supplied hex key

.
Screw the strimmer onto the thread in an anticlockwise direction.
ATTENTION! Left-hand thread!
Putting on the carrying harness
NOTE
The following adjustments can be made to make sure that you can
work without becoming fatigued. The settings may vary depending
on your body size.
Before starting work, adjust the carrying harness

to suit your body
size.
Balance the appliance with the fitted cutting tool so that the cutting
tool swings just over the ground without the need to move the appli-
ance with your hands.
1.) Put on the carrying harness

and close the clasps so that they click
into place (see fig. 3a).
2.) As shown in figure 3b, pull on the belt

, to position the carrying
harness

centrally on your body and adjust the upper body size.
3.) To tighten the two shoulder straps, pull on the two shoulder straps as
shown in figure 3c.
4.) To ensure to the correct position of the appliance on the carrying harness,
pull the belt as shown in figure 3d.
5.) Hook in the carabiner
(see figs. 3e–3g) and secure it with the red
strap
on the quick release mechanism.
6.) Now take the appliance and hang it so that the carrying lug
clicks
into the carabiner
, as shown in figure 3h. The carrying lug can
also be moved by loosening the screw
and sliding it to achieve the
optimum orientation of the appliance.
Setting the cutting height
Put on the carrying harness

and hook in the appliance (see section
"Putting on the carrying harness").
Use the various belt straps on the carrying harness

to adjust the
optimum working and cutting position (see section "Putting on the
carrying harness").
Perform a few circular movements without starting the engine in order to
find the ideal shoulder strap length (see fig. 6a).
The carrying harness

is equipped with a quick release mechanism.
Pull on the red strap if you have to release the appliance quickly
(see fig. 3i).
CAUTION!
Always use the carrying harness

when working with the device.
Put on the carrying harness

as soon as you have started the
engine and it is ticking over. Turn off the engine before removing the
carrying harness

.
Fuel and oil
Only use a mixture of unleaded petrol (at least RON 95) and special
2-stroke engine oil (JASO FD/ISO-L-EGD). Mix the fuel mixture in ac-
cordance with the fuel mix table.
Add the respective correct amounts of unleaded petrol and 2-stroke oil
to the supplied oil/petrol mixing canister

(see "Fuel mix table").
Then shake the canister well.
Fuel mix table
Mixing process: 40 parts petrol to 1 part oil
Petrol 2-stroke oil
0.5 litres 12.5 ml
Use
CAUTION!
Please pay attention to the statutory provisions in the relevant noise
protection regulations.
Before starting the appliance, always check that:
The fuel system is not leaking.
The protective equipment and cutting equipment is complete and in
perfect working order.
All screw connections are firmly tightened.
All moving parts can move smoothly and freely.
Starting when the engine is cold
CAUTION!
Never allow the starter pull cord to whip back. This could cause
damage.
1.) Fill the fuel tank
(see also the section "Fuel and oil").
2.) Push the fuel pump (primer)
6 times.
3.) Switch the On/Off switch
to "I".
4.) Pull the choke lever
into the position " ".
5.) Hold the appliance firmly and pull out the starter pull cord
to the
point of first resistance. Now pull hard on the starter pull cord
.
The appliance starts.
6.) If the engine does not start, repeat step 5.
7.) As soon as the engine is running, press first the safety lock-out
and
then the throttle
to activate the automatic choke.
If the engine does not start after several attempts, read the "Troubleshooting
guide" section.
CAUTION!
Always pull the starter pull cord
straight out. Hold the handle of
the starter pull cord
firmly when the starter pull cord
retracts.
Do not allow the starter pull cord to whip back.
NOTE
At very high ambient temperatures, it is possible that even a cold
engine has to be started without using the choke!
Starting when the engine is hot
(The appliance has been turned off for less than 15–
20 minutes)
1.) Switch the On/Off switch
to "I".
2.) The choke lever
does not need to be pulled out to start a warm motor.
3.) Hold the appliance firmly and pull out the starter pull cord
to the
point of first resistance. Now pull hard on the starter pull cord
. The
appliance should start after 1–2 pulls. If the appliance still hasn't started
after 6 pulls, repeat steps 1–7 under "Starting when the engine is cold".
17

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Florabest-FBK-4-C2---IAN-296309

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Florabest FBK 4 C2 - IAN 296309 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Florabest FBK 4 C2 - IAN 296309 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Florabest FBK 4 C2 - IAN 296309

Florabest FBK 4 C2 - IAN 296309 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Dansk - 78 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info