679143
16
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
FBK 4 C2
GB│IE│NI
 11
Tightening and checking the saw chain
WARNING!
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
Turn the chain-tensioner screw
in a clockwise direction using the
flat-blade screwdriver

to increase the tension.
The saw chain
must lie against the underside of the blade. Check
whether the saw chain
can be drawn over the blade
by hand.
NOTE
A new saw chain
stretches and must be tightened more frequently.
Lubricating the chain
Remove the oil filler cap .
Fill the oil tank
with approx. 100ml of organic chain oil

.
The chain lubrication can be increased or decreased using the oil
adjusting screw
.
Press and then turn the oil adjusting screw
clockwise to decrease
the chain lubrication.
Press and then turn the oil adjusting screw
anticlockwise to increase
the chain lubrication.
WARNING!
Never work without lubricating the chain first!
If the saw chain runs dry, the cutting equipment may become irrepar-
ably damaged within a short time. Always check chain lubrication
and oil level in the tank before starting work.
NOTE
Use only saw chain oil. Preferably biodegradable. Do not use waste
oil, motor oil, etc.
While working, check whether the chain lubrication is working
correctly.
Sharpening the saw chain
NOTE
A bench grinder can be attached to the bench grinder support
for
a secure grip during grinding.
You will find detailed information on sharpening in a sharpening set,
e.g. from Oregon.
Alternatively, you can use an electrical saw chain sharpening device
and follow the manufacturer's instructions.
If you have any doubts about carrying out the work, the saw chain
should be replaced.
Attaching the extension attachment
CAUTION!
Do not use the extension attachment/boom

in combination with
the 3-section cutting blade/strimmer attachment!
NOTE
Use the extension attachment/boom

for working at greater
heights.
Fit the extension attachment/boom

between the engine unit and
the hedge trimmer/pole pruner. The assembly is carried out in the
same manner as for the attachments described previously.
Fitting/removing the protective guard
WARNING!
When working with the 3-section cutting blade
, the blade guard
must be fitted. The blade guard is positioned under the metal panel
of the boom . The blade guard is now attached to the front boom
with the 2 screws . To do this, use the supplied hex key

.
Cutting equip-
ment
Protective equipment
3-section cutting blade Blade guard
Strimmer
Blade guard + cutting filament protect-
ive guard
C
WARNING!
Do not use any other cutting equipment apart from that which is
supplied with the product. The use of any other cutting equipment
or protective equipment is deemed to be improper and carries a
significant risk of accidents.
Installing/replacing the cutting blade
Fit/remove the 3-section cutting blade as shown in figures 1a–1f.
Find the hole in the drive plate

, align it with the opposite hole and
block it with the supplied hex key

.
Place the 3-section cutting blade on the drive plate

(see fig. 1b).
The inscription must be visible from above when holding the tool in the
working position (see fold-out page). Both sides of the 3-section cutting
blade can be used.
Fit the pressure plate

over the thread over the splined shaft (see fig.
1c).
Fit the pressure plate cover

(see fig. 1d).
Tighten the nut

with the spark plug spanner

anticlockwise ACH-
TUNG! Left-hand thread! (see fig. 1f).
The 3-section cutting blade
is fitted with a plastic cover on delivery.
This must be removed before use and refitted during periods when not
in use.
The plastic cover can now be removed.
CAUTION! SHARP EDGES, WEAR PROTECTIVE GLOVES
Fit the cutting filament protective guard
C
on the protective guard .
The cutting filament protective guard
C
must be fitted when working
with the cutting filament. The cutting filament protective guard
C
(pre-fitted on delivery) is fitted as shown in figure 2a.
Ensure that the cutting filament protective guard
C
is correctly clicked
into place. There is a blade
A
on the inside of the cutting filament pro-
tective guard
C
. This is covered with a safety cover
B
(see fig. 2a.).
Remove the safety cover
B
before starting work and replace it after
finishing work.
CAUTION! SHARP EDGES, WEAR PROTECTIVE GLOVES
To remove the cutting filament protective guard
C
from the protective
guard
, take a tool, such as a screwdriver, to carefully remove the
three mounting pins.
ATTENTION! RISK OF INJURY!
16

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Florabest-FBK-4-C2---IAN-296309

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Florabest FBK 4 C2 - IAN 296309 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Florabest FBK 4 C2 - IAN 296309 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Florabest FBK 4 C2 - IAN 296309

Florabest FBK 4 C2 - IAN 296309 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Dansk - 78 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info