383528
18
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
18
Procedure:
Place the machine onto the workpiece and position
it against a stop (kickback stop), switch the ma-
chine on, slowly press it down onto the set cutting
depth and push it forward in the cutting direction.
The markings [4-2] display the absolute front and
the absolute rear cutting points of the saw blade
(dia. 160 mm) at maximum cutting depth and using
the guide rail.
5.4 Sawing aluminium
When sawing aluminium, the following
measures must be taken for safety rea-
sons:
- Pre-connect a residual current circuitbreaker.
- Connect the machine to a suitable dust extrac-
tor.
- Clean the machine regularly of dust deposits in
the motor housing and in the protective cover.
Wear protective goggles.
- Aluminium must only be sawed with the special
saw blades from Festool designed for this pur-
pose.
When sawing panels, they must be lubricated with
petroleum, thin-walled profi les (up to 3 mm) can
be sawed without lubrication.
5.5 Plaster and cement-bonded fibre
boards
Due to the high build-up of dust, using a cover
(accessories) that is mounted on the side of the
protective cover is recommended.
6 Accessories
The order numbers of the accessories listed below
can be found in the Festool catalogue or on the
Internet under “www.festool.com”.
6.1 Parallel stop, table widener
A parallel stop can be used for section widths up
to 180 mm. The parallel stop can also be used as
a table widener.
6.2 Side-mounted cover, false joints
The cover that can be mounted on the side of the
protective cover improves the effect of dust extrac-
tion for 0° cuts. Simultaneously, the cover can be
used as a false joint stop for false joint widths from
18 mm onwards.
6.3 Guide system
The guide rails, which are available in different
lengths, allow for precise, clean cuts and simul-
taneously protect the workpiece surface against
damage.
In conjunction with the extensive range of acces-
sories, exact angled cuts, mitre cuts and fi tting
work can be completed with the guide system. The
option of securing using G-clamps [4-4] ensures a
rm hold and safe working.
The guide clearance of the saw table on the guide
rails can be set with the two setting jaws [1-3].
The guide rails are equipped with a splinterguard
[1-5], which has to be cut to size before the fi rst
use:
- Set the speed of the machine to level 6,
- Place the machine on the rear end of the guide
rail,
- Switch the machine on, press it down to the set
cutting depth and cut the splinterguard along the
full length without interruption.
The edge of the splinterguard now corresponds
exactly to the cutting edge.
6.4 Multifunction table
The mutifunction table MFT/3 makes clamping
the workpiece easy and allows you to saw large
and small workpieces safely and precisely using
the guide system. Its many fi elds of application
make economical and ergonomically convenient
work possible.
6.5 Saw blades, other accessories
In order to be able to saw different materials
quickly and cleanly, Festool offers saw blades that
are specially designed for your machine.
The order numbers for these and for other acces-
sories that allow you to use your Festool portable
circular saw effectively and in many ways, can be
found in the Festool catalogue or on the Internet
under “www.festool.com”.
7 Maintenance and care
Always remove the plug from the mains
supply socket before carrying out any
work on the machine!
Any maintenance or repair work requir-
ing the motor housing to be opened may
only be carried out by an authorised serv-
ice workshop.
Always keep the machine and the ventilation slots
clean.
The tool is fi tted with special motor brushes with
18

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Festool-ts-55-q

Zoeken resetten

  • Mijn Festool TS 55 EBQ komt trager dan normaal op toeren. Wat kan daarvan de oorzaak zijn? Koolborstels? Oplossing? Gesteld op 20-2-2023 om 15:53

    Reageer op deze vraag Misbruik melden
  • hoe vervang ik koolborstels van de Festo TS 55 invalzaag Gesteld op 11-5-2014 om 15:51

    Reageer op deze vraag Misbruik melden
    • Zorg dat de machine niet is aangesloten met de plug-in steker. Open dan de kap met 4 schroeven van de machine waar het logo "FESTOOL"op staat. Dan zie je 2 koolborstels zitten. Deze worden bevestigd met ieder 1 schroef. De bedrading kun je loshalen, deze zitten geklemd. De een glijd er zo uit, de andere moet je een beetje helpen. Nieuwe koolborstels (Festoolnummer:491704) plaatsen in omgekeerde volgorde. Succes! ;-) Geantwoord op 4-12-2015 om 20:26

      Waardeer dit antwoord (36) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool ts 55 q bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool ts 55 q in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info