383528
17
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
17
stop notches along in 1 mm-steps).
The sawing unit can now be pressed down to the
set cutting depth.
A grub screw (M4x8 to M4x12) can be screwed into
the hole [2-2] on the cutting depth stop. By turning
the grub screw, the cutting depth can be set even
more exactly (± 0.1 mm).
4.3 Cutting angle
The sawing unit can be swivelled between 0° and
45°:
- Loosen rotary knobs [2-4, 2-6],
- Swivel sawing unit to the desired cutting angle
[2-5],
- Retighten rotary knobs.
Note: both end positions (0° and 45°) are set at
the factory and can be readjusted by the aftersales
service team.
4.4 Changing the saw blade
- Before changing the saw blade, set the machine
to the 0° position.
- Move lever [3-2] as far as it will go,
- Push switch lock [3-1] up and push sawing unit
down until it locks into place,
- Loosen screw [3-4] with Allen key [3-3],
- Remove saw blade,
- Clean ange [3-8, 3-10],
- Insert new saw blade.
The direction of rotation of the saw blade
[3-9] and the machine [3-7] must be the
same.
- Insert outer fl ange [3-10] such that the locking
pins engage into the notches on the inner fl ange
[3-8].
- Tighten screw [3-4],
- Put lever [3-2] back.
4.5 Setting the spacer wedge
- Move lever [3-2] as far as it will go,
- Push switch lock [3-1] up and push sawing unit
down until it locks into place,
- Loosen screw [3-6] with Allen key [3-3],
- Set spacer wedge [3-5] as shown in diagram 3,
- Tighten screw [3-6],
- Put lever [3-2] back.
4.6 Dust extraction
Always connect the machine to a dust ex-
tractor.
A Festool dust extractor with an extractor hose di-
ameter of 36 mm or 27 mm (36 mm recommended
due to the reduced risk of clogging) can be con-
nected to the rotating extractor connector [4-1]
4.7 Mounting the splinterguard
The splinterguard (accessories) signifi cantly im-
proves the quality of the cutting edge of the sawn
workpiece on the upper side for 0° cuts.
- Attach splinterguard [5-1] onto the protective
cover,
- Place machine onto the workpiece or the guide
rail,
- Press splinterguard down until it sits on the work-
piece and tighten it with the rotary knob [5-2].
- Saw splinterguard in (machine to maximum cut-
ting depth and speed range 6)
5 Working with the machine
Always secure the workpiece in such a
manner that it cannot move while being
sawed.
The machine must always be held with
both hands by the designated handles [1-
1, 1-7].
Always push the machine forwards [1-2],
never pull the machine backwards towards
you.
Adapt the fast-feed speed to prevent the
cutters on the saw blade from overheating
and prevent plastic materials from melting
during cutting.
5.1 Sawing along a scribe mark
The cutting indicator [4-3] displays the cutting line
for 0° and 45° cuts (without guide rail).
5.2 Sawing sections
Place the machine with the front part of the saw
table on the workpiece, switch the machine on,
press it down onto the set cutting depth and push
it forward in the cutting direction.
5.3 Sawing cut outs (plunge cuts)
In order to avoid kickbacks, the following instruc-
tions absolutely must be observed when plunge
cutting:
- The machine must always be placed with the rear
edge of the saw table against a fi xed stop.
When working with a guide rail, the machine must
be positioned against the kickback stop [1-4],
which is clamped on the guide rail.
- The machine must always be held securely with
both hands and only plunged slowly.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Festool-ts-55-q

Zoeken resetten

  • Mijn Festool TS 55 EBQ komt trager dan normaal op toeren. Wat kan daarvan de oorzaak zijn? Koolborstels? Oplossing? Gesteld op 20-2-2023 om 15:53

    Reageer op deze vraag Misbruik melden
  • hoe vervang ik koolborstels van de Festo TS 55 invalzaag Gesteld op 11-5-2014 om 15:51

    Reageer op deze vraag Misbruik melden
    • Zorg dat de machine niet is aangesloten met de plug-in steker. Open dan de kap met 4 schroeven van de machine waar het logo "FESTOOL"op staat. Dan zie je 2 koolborstels zitten. Deze worden bevestigd met ieder 1 schroef. De bedrading kun je loshalen, deze zitten geklemd. De een glijd er zo uit, de andere moet je een beetje helpen. Nieuwe koolborstels (Festoolnummer:491704) plaatsen in omgekeerde volgorde. Succes! ;-) Geantwoord op 4-12-2015 om 20:26

      Waardeer dit antwoord (36) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool ts 55 q bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool ts 55 q in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info