383528
16
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
16
in the workpiece. The riving knife is ineffective
in preventing kickback during short cuts.
e) Do not operate the saw if riving knife is bent.
Even a light interference can slow the closing
rate of a guard.
2.3 Noise and vibration information
Typical values established in compliance with EN
60745:
Sound-pressure level/ Sound-power level
TS 55 EBQ/TS 55 EQ 95/106 dB(A)
TS 55 Q 96/107 dB(A)
Measuring uncertainty allowance K = 3 dB
Wear ear protection.
Overall vibration levels (vector sum for three direc-
tions) measured in accordance with EN 60745:
Vibration emission level (3 directions)
Sawing wood a
h
< 2,5 m/s²
Sawing metal a
h
< 2,5 m/s²
Uncertainty K = 1,5 m/s²
The emission values specifi ed (vibration, noise)
were measured in accordance with the test con-
ditions stipulated in EN 60745 and are intended
for machine comparisons. They are also used for
making preliminary estimates regarding vibration
and noise loads during operation.
The emission values specifi ed refer to the main
applications for which the power tool is used. If the
electric power tool is used for other applications,
with other tools or is not maintained suffi ciently
prior to operation, however, the vibration and noise
load may be higher when the tool is used. Take into
account any machine idling times and downtimes to
estimate these values more accurately for a speci-
ed time period. This may signifi cantly reduce the
load during the machine operating period.
3 Power supply and start-up
The mains voltage must correspond to
the specifi cation on the rating plate.
Always switch the machine off before
connecting or disconnecting the mains
lead!
See Fig. 2 for connection and disconnection of the
power cable.
The switch [1-8] is for switching on/off (push = ON,
release = OFF).
The switch can only be activated after the switch
lock [1-9] has been pushed up.
Activating the switch lock simultaneously locks
the plunging equipment and the sawing unit can
be moved down against the spring force. This
causes the saw blade to emerge from the protec-
tive cover.
When the machine is lifted, the sawing unit springs
back into the starting position.
Only guide the machine against the work-
piece when it is switched on.
Check the installation fi xture prior to use
and do not use the machine if the fi xture
does not function correctly.
4 Machine settings
Always pull the plug out of the socket be-
fore making settings.
4.1 Electronics
The TS 55 EBQ/TS 55 EQ features full-wave
electronics with the following properties:
Smooth start-up
The smooth start-up ensures the machine starts
up jolt-free.
Speed adjustment
You can regulate the speed steplessly between 2000
and 5200 rpm using the adjusting wheel [1-6]. This
enables you to optimise the cutting speed to suit
the material (see table 1).
Constant speed
The pre-selected speed remains constant whether
the machine is in operation or in neutral position.
Temperature cut-out
To prevent overheating, the safety electronics
switches the machine off when it reaches a critical
motor temperature. Let the machine cool down
for approx. 3-5 minutes before using it again. The
machine requires less time to cool down if it is
running, i.e. in neutral position.
Current limiting
Current limiting prevents permissibly high current
consumption under extreme overload. This can
lead to a decrease in the motor speed. The motor
immediately restarts after the load is removed.
Brake (only TS 55 EBQ)
After switching-off the tool, the saw blade is elec-
tronically brought to a standstill in 1.5 – 2 sec-
onds.
4.2 Cutting depth
The cutting depth can be set at 0 – 55 mm:
- Press the cutting depth stop [2-3] and move it to
the desired cutting depth (the values specifi ed on
the scale [2-1] apply to 0° cuts without guide rail),
- Release the cutting depth stop (the cutting depth
16

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Festool-ts-55-q

Zoeken resetten

  • Mijn Festool TS 55 EBQ komt trager dan normaal op toeren. Wat kan daarvan de oorzaak zijn? Koolborstels? Oplossing? Gesteld op 20-2-2023 om 15:53

    Reageer op deze vraag Misbruik melden
  • hoe vervang ik koolborstels van de Festo TS 55 invalzaag Gesteld op 11-5-2014 om 15:51

    Reageer op deze vraag Misbruik melden
    • Zorg dat de machine niet is aangesloten met de plug-in steker. Open dan de kap met 4 schroeven van de machine waar het logo "FESTOOL"op staat. Dan zie je 2 koolborstels zitten. Deze worden bevestigd met ieder 1 schroef. De bedrading kun je loshalen, deze zitten geklemd. De een glijd er zo uit, de andere moet je een beetje helpen. Nieuwe koolborstels (Festoolnummer:491704) plaatsen in omgekeerde volgorde. Succes! ;-) Geantwoord op 4-12-2015 om 20:26

      Waardeer dit antwoord (36) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool ts 55 q bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool ts 55 q in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info