778530
26
Verklein
Vergroot
Pagina terug
1/185
Pagina verder
7 Settings
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
7.1 Electronics
Smooth start-up
The electronically controlled smooth start-up
function ensures that the power tool starts up
smoothly.
Constant speed
The motor speed is electronically kept con
stant. This ensures a uniform cutting speed
even when under load.
Speed control
You can continuously adjust the speed within
the speed range using the adjusting
wheel [1-12] (see "Technical data"). This ena
bles you to optimise the cutting speed to suit
each surface.
Speed range per material
Solid wood (hard, soft) 6
Chipboard and hardboard 3–6
Laminated wood, blockboard, veneered
and laminated panels 6
Laminate, mineral materials 4–6
Plaster- and cement-bonded chipboard
and fibreboard 1–3
Aluminium panels and profiles up to
15 mm 4–6
Plastics, fibre-reinforced plastics, paper
and fabric 3–5
Acrylic glass 4–5
Current limiting
Current limiting prevents excessive current
consumption under extreme overload, which
can lead to a decrease in the motor speed. The
motor immediately restarts after the load is re
moved.
Brake
The saw comes with an electronic brake. The
saw blade is stopped electronically within ap
proximately two seconds of switching off the
machine.
Temperature cut-out
The power supply is restricted and the speed
reduced if the motor exceeds a certain temper
ature. The power tool continues operating at re
duced power to allow the ventilator to cool the
motor quickly. The power tool starts up again
automatically once the motor has cooled suffi
ciently.
7.2 Adjusting the cutting depth
The cutting depth can be set at 0 – 55 mm at the
cutting depth stop [3-1].
The saw unit can now be pushed downwards as
far as the cutting depth that is set.
Cutting depth without guide rail
max. 55 mm
+FS
Cutting depth with FS guide rail
max. 51 mm
7.3 Setting the cutting angle
between 0° and 45°:
Unscrew the rotary knobs [4-1].
Swivel the saw unit to the desired cutting
angle [4-2].
Tighten the rotary knobs [4-1].
Both positions (0° and 45°) are set at the
factory and can be readjusted by the cus
tomer service team.
When making angled cuts, slide the view
ing window/splinter guard to the highest
position.
To undercut -1° and 47°:
Swivel the saw unit to the end position (0°/
45°) as described above.
Pull out the release button [4-3] slightly.
For -1° undercuts, also pull the release
button [4-4].
The saw unit engages in the -1°/47° position.
Tighten the rotary knobs [4-1].
7.4 Selecting the saw blade
Festool saw blades are identified by a coloured
ring. The colour of the ring represents the ma
terial for which the saw blade is suited.
Refer to the necessary saw blade data (see sec
tion 3.1).
English
26
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TSC 55 KEB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TSC 55 KEB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info