796183
22
Verklein
Vergroot
Pagina terug
1/129
Pagina verder
Constant speed
The preselected motor speed is kept constant
through electronic control. This ensures a uni
form speed even when under load.
Temperature cut-out
To avoid the motor overheating, the power con
sumption is limited at an excessive motor tem
perature (e.g. if the pressure is too high while
working). If the temperature continues to rise,
the power tool switches off. It can only be
switched on again once the motor has cooled
sufficiently.
6.3 Handle position
Loosen the handle screw [1-5] as much as nec
essary and set the handle [1-6] to a suitable
working position by tilting it. Then tighten the
handle screw [1-5] again.
6.4 Sanding discs
Depending on the application area, various
sanding discs are available. Use solely discs of
Festool, which guarantees the sanding output
of the RG 130 ECI.
Recommended sanding disc types
Sanding
disc
Field of application Speed
range
DIA STONE-D130
Very hard materials,
e.g. concrete with a
strength higher than
C20, cast concrete
6
DIA HARD-D130
Hard materials, e.g.
concrete with a
strength higher than
C10, hard screed
6
DIA ABRASIV-D130
Soft materials with a
higher level of abrasion,
e.g. fresh concrete, ad
hesive coatings, hard
plaster, sandstone
6
Sanding
disc
Field of application Speed
range
DIA PAINT-D130
Large and thick layers
of paint or varnish, e.g.
on floorboards, wooden
façades and doors
4–6
DIA THERMO-D130
Tough and thermoelas
tic materials, e.g. pro
tective coatings, elastic
adhesives
5–6
Installing the abrasive wheel
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
WARNING
Risk of injury from the fragile sanding tool
Ensure that the sanding tool's expiry date
has not been exceeded.
Clean the flange [2-1] and fastening
nut [2-4] as well as sanding disc fastening
areas [2-2].
Mount sanding disc. Flange fitting must fit
the sanding disc aperture.
Press in the spindle blocking plunger [2-3].
Press in the blocking plunger only when de
vice is switched off and spindle not active.
Turn the spindle [2-6] until blocking plung
er fits in.
Screw the fastening nut by fitting it from the
sanding disc on the spindle.
Fasten the fastening nut with key [2-5].
Before starting the device, make sure the
sanding disc rotates smoothly.
The intermediate layers supplied with the
sanding discs are not required.
6.5 Brush
Lifting the front brush
For wall lifting, it is possible to lift the lifting
segment [3-1] (see figure [3]).
English
22
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool RG 130 ECI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool RG 130 ECI in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2.9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info