778626
17
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
8.2 Changing the insertion tool
CAUTION
Hot and sharp tools
Risk of injury
Do not use any blunt or faulty insertion
tools.
Wear protective gloves.
Carefully remove the protective resin from
the cutting edge of new tools.
CAUTION
There is a risk of injury and negative impact
on health associated with using tools that
are not supplied or recommended by
Festool.
Damage to machine caused by increased vi
bration load
Always use original Festool tools.
CAUTION
Risk of crushing hands and fingers
If you switch on the power tool when the
clamping lever is open, the clamping lever is
closed by spring force. Open clamping jaws
are spring-loaded.
Never switch on the power tool with the
clamping lever open.
Never reach into the area around the
clamping jaws.
Removing the insertion tool [3a]
Open the clamping lever [3-1].
The insertion tool drops down.
Close the clamping lever until it clicks into
place.
If the power tool switches on without the
insertion tool, the clamping jaws [3-2] may
open. This makes a popping sound.
Inserting the insertion tool [3b]
If the clamping jaws [3-2] are open, open and
close the clamping lever [3-1].
Close the clamping lever until it clicks into
place.
Push the device onto the tool until it clicks
into place.
The tool can be offset in 30° increments
and secured in the most effective working
position.
The protection (against accidental contact)
on the saw blade may become twisted if
wear has occurred, see fig. [4]
9 Working with the machine
Observe the following information:
Only guide the power tool towards the
workpiece when it is switched on.
A significant increase in the force required
to advance the machine and slow working
progress are indicators that the blades are
worn.
Hold the power tool by the gripping sur
face [1-3] with both hands to ensure safe
guidance. Do not cover the cooling air
openings [1-4] with your hand. Otherwise
there is a risk of the machine overheating.
Do not hold the power tool by the battery
pack.
Always secure the workpiece in such a way
that it cannot move during machining.
10 Acoustic warning signals
If the power tool switches off due to one of the
following operating states, a warning signal
sounds when switching on the tool and the
power tool switches off again.
Battery pack not accepted
Insert the correct battery pack model.
Battery pack empty
Change the battery pack.
Charge the battery pack.
Battery pack fault
Change the battery pack.
Use the charger to check that the battery
pack is fully functional once it has cooled
down.
Battery pack overheated
Let the battery pack cool down.
Power tool overheated
You must allow the power tool to cool down
before starting it up again.
Power tool fault
Contact a Festool service workshop or spe
cialist dealer.
Power tool jammed
Eliminate the cause of the jam.
If the power tool switches of when it be
comes jammed, no warning signal sounds.
English
17
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool OSC 18 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool OSC 18 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 12.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info