778812
23
Verklein
Vergroot
Pagina terug
1/126
Pagina verder
23
9.2 Motor electronics
Starting current limitation
Electronically controlled continual running se-
cures device acceleration without back thrust.
Due to starting current limitation in the device,
16A protection is suffi cient.
WARNING
Devices without starting current limitation
need higher protection – at least 16A circuit
breaker.
Speed control
You can regulate the speed steplessly within the
speed range using the adjusting wheel [1-15] (see
Technical data). This enables you to optimise the
speed to suit the respective material. Please also
note the specifi cations on the tools.
Switching off during back thrust
During sudden drop of revolutions, for example
blocking in dividing cut, the current input in mo-
tor stops. For re-starting, the device must be fi rst
switched off and again switched on.
Protection against re-starting
Prevent uncontrolled starting of the device after
current supply cut off. For re-starting, the device
must be fi rst switched off and again switched on.
Constant speed
The preselected motor speed remains constant
through electronic control to ensure a uniform
cutting speed even when under load.
Protection from overloading dependant on tem-
perature
The safety electronics switches to cooling regime
when the critical temperature is reached. Motor
continues running at approximately 50 % revolu-
tions, constant electronics is deactivated.
After cooling to approximately 10 20 s, the device
is fully operational.
Heat protection for devices heated during opera-
tion, reacts adequately sooner.
9.3 Turning the gear box
For special cases, the gearbox can be turned in
steps of 90°. This achieves a better handling posi-
tion of the switch.
For such work, we recommend to use the Festool
service.
Remove four screws.
Carefully, turn the gearbox into required posi-
tion. Make sure the gearbox does not separate
from motor box by more than approximately
1mm.
Insert and fasten the four screws -fi gure [8].
9.4 Aperture cover
If you wish to see the cutting area, take off the
aperture cover [2-3]. Only handle this cover when
the disc is not running.
Be careful about spattering dust particles.
10 Service and maintenance
WARNING
Risk of accident, electric shock
Always pull the plug out of the socket before
performing any type of work on the machine.
All maintenance and repair work which re-
quires the motor housing to be opened, must
only be carried out by an authorised service
workshop.
- Wrapped electric tools can be stored in a dry
place without heating, with temperatures not
lower than –5°C. Unwrapped electric tools can
only be stored in dry places with temperatures
not lower than +5°C, without sudden changes
in the temperature.
-To ensure the airfl ow is suffi cient, cooling
openings of the motor must be always clean
and free.
-The machine is equipped with special self-
disconnecting brushes. When the brushes are
worn, the power supply is automatically discon-
nected, and the machine is stopped.
-If the suction fl ange height adjustment system
does not operate smoothly, the fl ange must be
removed and cleaned.
Customer service and repair. Only through
manufacturer or service workshops:
Please fi nd the nearest address at: www.
festool.com/service
EKAT
1
235
4
Use only original Festool spare parts! Or-
der No. at:
www.festool.com/service
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool DSC-AG 125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool DSC-AG 125 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 7.06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info